The introduction of blast furnace Production capacity t/(m2d) Lead sinter reduction smelting 50-60 up to 90 Lead pellet reduction smelting 25-40 up to 50 Copper raw concentrate isf smelting 45-55 up to 60 Depend on your need
The blast furnace is one of the most important metallurgical equipment, it has the following characteristics:high thermal efficiency, high specific productivity(specific capacity), high metal recovery rate, low cost, less covering area and so on. Depend on your need
The introduction of blast furnace Blast furnace is the shaft furnace of metallurgical equipment.Blast furnace is used for melting furnace burden(ore, sinter or pellet) that contains metal components, melting need to add air or happen in oxygen-rich e copper and other materials processing.Blast furnace burden is generally block, fuel is coke.Burden is added in batches from :0.6 m2, 1.2 m2, 2 m2, 2.6 m2, 3.2 m2, 5.6 m2, 8 m2, 10 m2, 11m2 and so on.Our company can design and produce different specification and structures blast furnace based on customer¡¡¡ê¡ès actual demand. Depend on your need
Er and other materials processing.Blast furnace burden is generally block, fuel is coke.Burden is added in batches from the top, forming a stock column.Air is added from tuyere below, coke burns in the tuyere(outlet)area, forming a high-temperature melting area;furnace burden reacts violently here, continue to melt.When you reduction smelting, melt was clarified in the hearth, metal and slag were released. When you matte smelting, the melt flows into the external crucible from internal crucible, to clarify the separation of matte and slag.Hot flue gas through the melt and reach th Lead pellet reduction smelting 25-40 up to 50 Copper raw concentrate isf smelting 45-55 up to 60 emand. Depend on your need
Ount of cold pig iron and ore. The converter is mainly composed of furnace body, transmission device, supporting device, open gear brush, universal joint, lubrication system.Converter has below advantages:high efficiency, easy operation, wide adaptation of ecious metal(gold and silver), copper concentrate sulfur melting, refining crude copper etc.. Converter¡¡¥s processing capacity depends on the materials type and associated equipment type.Generally determine the specification depending on the loading capacity(matte), specifications in common use are 10t¡¡é20t¡¡é30t¡¡é50t¡¡é80t¡¡é100t etc..Our company can design and produce different specification converter based on customer¡¡¥s actual demand. Depend on your need
We are engaged in making Lead available in several forms including LME registered and non registered 99.97% and 99.99% as well as secondary ingots, foil, granules, powder, rod, shot, sheet, and wire. Lead is a bluish-white lustrous metal. It is very soft, highly malleable, ductile, and a relatively poor conductor of electricity. It is very resistant to corrosion but tarnishes upon exposure to air. Alloys include pewter and solder.
We hold immense expertise in making available Copper in many forms including LME registered and non registered cathodes, billets, rods, cakes, bars, foil, sheet, granules, plates, powder, shot, turnings, wire, insulated wire, mesh and “evaporation slugs”. Copper is one of the most important metals. Copper is reddish with a bright metallic lustre. It is malleable, ductile, and a good conductor of heat and electricity (second only to silver in electrical conductivity). Its alloys, brass and bronze, are very important. Monel and gun metals also contain copper. The most important compounds are the oxide and the sulphate, (blue vitriol
The Incinerated scrap or E46, is the by-product derived from the reprocessing of incinerated domestic waste. After the combustion process, the furnace output (IBA Incinerator bottom ash) is firstly washed, magnetically separated and screened to separate any no ferrous material. At a visual inspection, the material is fragmentized, with iron and steel parts, resulting partly cut or in shredded form. The stock appears heterogeneous and contains all kind of cut or dismantled steel parts such as sheets, bars, frames, wires, bolts and other iron/steel household residues. The incinerated scrap is eventually oxidized, due to the thermal and cooling treatments, that the material has been submitted to. The burnt scrap also contains minor slag parts, ash and iron oxide, due to the recovery process. Such components are inherent and adhere to the scrap surface. The total impurities, can be sorted, but not fully removed. The consignment does not contain any type of arms, ammunition, mines, shells, cartridges, radioactive contaminated, or any other explosive material in any form either used or otherwise. The collected stock, is stored in open air, on cemented flooring. It can be loaded loose in 20â?? heavy duty container. Please feel free to contact us for further details.
We offer a wide plethora of Zinc in many forms including LME registered and non registered Special High Grade Ingots and Jumbos, cathodes, dust, foil, granules, powder, pieces, anodize activated powder, shot, and a mossy form. Zinc is a bluish-white, lustrous metal. It is brittle at ambient temperatures but is malleable at 100 to 150°C. It is a reasonable conductor of electricity, and burns in air at high red heat with evolution of white clouds of the oxide. Plating thin layers of zinc on to iron or steel is known as galvanizing and helps to protect the iron from corrosion.
