Copper pipe is almost pure copper manufactured to the requirements of astm b 42 - standard specification for seamless copper pipe, standard sizes. It may be manufactured from any of five (5) copper alloys (c10200, c10300, c10800, c12000, c12200) that all conform to the chemical composition requirements of alloys containing a minimum of 99.9% copper (cu) and a maximum of 0.04% phosphorous (p). Available sizes are 1/8" to 12" diameters in regular wall thickness and 1/8" to 10" in extra strong wall thickness. The standard length for copper pipe is 12 feet. Copper pipe is suitable for plumbing, boiler feed lines, refrigeration and for similar purposes. Joints in seamless copper pipe can be threaded, flanged or brazed to fittings of the appropriate joint configuration. Usually use plastic bag or wooden case
Copper water tube is a seamless, almost pure copper material manufactured to the requirements of astm b 88 - standard specification for seamless copper water tube, of three basic wall thickness dimensions designated as types k, l, and m. Type k is the thickest and type m is the thinnest with type l being of intermediate thickness. All three types of tube are manufactured from copper alloy c12200 having a chemical composition of a minimum of 99.9% copper (cu) and silver (ag) combined and a maximum allowable range of phosphorous (p) of 0.015 % - 0.040 %. Plastic bag or wooden case
Seamless copper tube manufactured to the astm b 75 - standard specification for seamless copper tube may be either round, square, or rectangular and is suitable for general engineering applications. It may be manufactured from any one of the following alloys: c10100, c10200, c10300, c10800, c12000, or c12200 unless specified otherwise on the original contract or purchase order. Tubes meeting this standard may be furnished in any of several tempers (h55, h58, h80, o60, or o50) ranging from light drawn (usually limited to round tubes) to light annealed. It is the responsibility of the purchaser, when ordering, to provide the requirements for alloy (uns#), temper, dimensions (diameter, wall thickness, or distance between parallel surfaces), form (straight lengths or coils), and total length or number of pieces of any particular size. It is this requirement that forces this tube to be a special order tube and not a standard stocked material. It is usually limited to use in specific manufacturing processes or production line type applications. Plastic bag or wooden case
Seamless brass tube Seamless brass tube is manufactured to the requirements of astm b 135 - standard specification for seamless brass tube and may be either round, square, or rectangular and is suitable for general engineering applications. It may be manufactured from any one of the following alloys: c22000, c23000, c26000, c27000, c27200, c27400, c28000, c33000, c33200, c37000, or c44300 and these alloys contain copper (cu) concentrations of between 60% and 90% with various percentages of zinc (zn), lead (pb), and tin (sn) permitted, depending on the alloy. Tubes meeting this standard may be furnished in any of several tempers ranging from light drawn to light annealed. It is the responsibility of the purchaser, when ordering to provide the requirements for alloy (uns#), temper, dimensions (diameter and wall thickness, or distance between parallel surfaces), form (straight lengths or coils), and total length or number of pieces of any particular size. Plastic bag or wooden case
Copper tube used for air conditioning and refrigeration applications in the field (sometimes called "refer" or "acr" tube) is an almost pure copper material meeting the requirements of astm b 280 - standard specification for seamless copper tube for air conditioning and refrigeration field service. It is manufactured from copper alloy c12200 having a chemical composition of a minimum of 99.9% copper (cu) and silver (ag) combined and a maximum allowable range of phosphorous (p) of 0.015 % - 0.040 %. B 280 tube is produced in straight lengths or coils in tempers h58 or o60 respectively, although annealed straight Air conditioning and refrigeration tube (astm b 280) either coiled or straight length is further required to be cleaned and capped prior to shipping. Pancake coil wrapped with plastic bag both end capped then put into carton box for several pieces
We hold immense expertise in making available Copper in many forms including LME registered and non registered cathodes, billets, rods, cakes, bars, foil, sheet, granules, plates, powder, shot, turnings, wire, insulated wire, mesh and “evaporation slugs”. Copper is one of the most important metals. Copper is reddish with a bright metallic lustre. It is malleable, ductile, and a good conductor of heat and electricity (second only to silver in electrical conductivity). Its alloys, brass and bronze, are very important. Monel and gun metals also contain copper. The most important compounds are the oxide and the sulphate, (blue vitriol
Size Outside diameter 2 to 800mm, wall thickness 1mm to 220mm, Length 1 meter to 6 meter. All sizes can be according to customer's requirements. Hardness 1/16 hard,1/8 hard,3/8 hard,1/4 hard,1/2hard,full hard. Surface Polished,bright,oiled,hair line,brush,mirror,or as required Export to Ireland,Singapore,Indonesia,Ukraine,Saudi Arabia,Spain,Canada,USA, Brazil,Thailand,Korea,Italy,India,Egypt,Oman,Malaysia,Kuwait,Canada, Viet Nam, Peru Package Plastic film with Wooden case or wooden pallet Delivery time Prompt delivery or upon your order quantity. MOQ Negotiable Quality Control Mill Test Certification is supplied with shipment,Third Part Inspection is acceptable. Application widely used inair conditioners,refrigerators,electric,solar water heater, polished pipe an be used in decorative,such as stair rail. Also can be made according to your required. Shape Round, Square, Flat, Hexagon, Oval
Grade C10100,C10200,C10300,C10400,C10500,C10700,C10800,C10910,C10920,C10930, C11000,C11300,C11400,C11500,C11600,C12000,C12200,C12300,C12500,C14200, C14420,C14500,C14510,C14520,C14530,C17200,C19200,C21000,C23000,C26000, C27000,C27400,C28000,C33000,C33200,C37000,C44300,C44400,C44500,C60800, C63020,C65500,C68700,C70400, C70620,C71000,C71500,C71520,C71640,C72200 T1,T2,T3,TU1,TU0,TU2,TP1,TP2,TAg0.1, Shape Flat plate Temper O-H112; T3-T8; T351-T851 Size thickness 0.3mm~100mm; Width 50mm~2500mm; Length 1000mm~12000mm Surface Mill finish, polished, anodizing, brushing, sand blasting, powder coating,etc Payment terms T/T,L/C,western union, Paypal Price terms CFR,FOB,CIF,Ex-work,CNF Application 1)Further making utensil. 2)Solar reflective film 3)The appearance of the building 4)Interior decorating:ceilings,walls,etc. 5)Furniture cabinets 6)Elevator decoraction 7)Signs,nameplate,bags making. 8)Decorated inside and outside the car 9)Household appliances:refrigerators,microwave ovens,audio equipment,etc. 10)The consumer electronics:mobile phones,digital cameras,MP3,U disk,etc.
Length: As Required Cu (Min): 99.9% Alloy Or Not: Non-Alloy Ultimate Strength (MPa): 205 Elongation (%): 45% Wall Thickness: 0.2mm~910mm Outside Diameter: 2mm*4mm~1016mm*1219mm Processing Service: Bending, Punching, Cutting Standard: JIS ASTM DIN EN ISO Material: C10200/C11000/C12000/C12200/TU1/TU2/T2/custom Surface: Polished Feature: High Srength Technique: Cold Rolled Hot Rolled Size: Custom Size
