APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
Tiles Adhesive (CT-01),(02),(03), Tiles Epoxy Grout, Tiles Grout (Light Color), Tile Grout (Dark Color), Tiles Epoxy Grout Sparkle, Block Jointing Mortar, Wall Putty, Floor Hardener Non-Metallic, Tile Spacer (2mm, 3mm, 4mm,5mm), SBR. Etc. Products are available in stock.
Construction Chemicals
In co-operation with major manufacturers in Turkey, FALMER is able to supply a wide range of products, including construction chemicals. Our aim is to supply the most excellent thermal insulation materials and construction chemicals and to bring them together with the end consumer. To contribute to the national economy by minimising the increasing energy demand of our world with our insulation materials. WHITE SEALANT 450 GR COLORED SEALANT 450 GR SILICONE CLEAR 280 GR POLYURETHANE LIQUID NAIL 450 GR SILICONE-BASED JOINT FILLER 380 GR CORNICE ADHESIVE 450 GR STYROFOAM CORNICE ADHESIVE 450 GR WOOD GLUE 100 GR WOOD GLUE 350 GR WOOD GLUE 700 GR SPRAY PAINT INTERMEDIATE COLORS 200 ML (160 GR) SPRAY PAINT INTERMEDIATE COLORS 400 ML (300 GR) SPRAY PAINT METALLIC â?? GOLD 200 ML (160 GR) SPRAY PAINT METALLIC â?? GOLD 400 ML (300 GR) CLEAR VARNISH 200 ML (160 GR) CLEAR VARNISH 400 ML (300 GR) PAINT REMOVER 200 ML (160 GR) PAINT REMOVER 400 ML (300 GR) POLYURETHANE FOAM 600ML SILICONE SPRAY 500 ML (380 GR) BRAKE PAD AND CLUTCH CLEANER 500 ML (390 GR) LABEL AND STICKER REMOVER 200 ML (160 GR) LIQUID GREASE 200 ML (160 GR) LIQUID GREASE 400 ML (350 GR) RUST REMOVER 200 ML (170 GR) RUST REMOVER 400 ML (320 GR) G-60 LUBRICANT 200 ML (170 GR) G-60 LUBRICANT 400 ML (320 GR) FAST ADHESIVE 200 ML (35 GR JAPON) FAST ADHESIVE 400 ML (75 GR JAPON) MOLD RELEASE 400 ML (350 GR) CHAIN LUBRICANT400 ML (350 GR) WATERPROOFING SPRAY 400 ML (350 GR) CHEMICAL ANCHOR LIGHTER GAS 270 ML CAMPING GAS 227GR ZINC SPRAY 400ML (350GR) GAS DUSTER SPRAY 400ML DRAIN CLEANER (500 GR) DRAIN CLEANER (1000 GR) DRAIN CLEANER (2000 GR)
Bondacoat Ar Bondacoat Ep Bondacoat Pva Bondacoat Sbr Epogrout Hs Rendragrout Hf (Adhesive & Grouts) Tile Adhesive Ep Tile Grout Ep Epomortar Fc Eposcreed 10 Fillgrout Ep10 Fillgrout Pu40 Rendacoat Fc Rendagrout Hf (Concrete Repairs) Concoat Ep100 Concoat Ep150 Concoat Ep250 Concoat Resin Concoat Sl Elastoguard Pu Prime Ep100 Tg Prime Ep100 Prime Eps Prime Eps40 Proofseal Pu Concoat Eps Concoat Ept500 Deguard Sheild Sn- Wr636 Deguard Sheild Sn Waterbased- Wr637 Concoat Slc90 Elastocryl 700 Elastocryl 800 Elastocryl 900 Epocoat Epwp Epoflex 500 Proofseal Pt Epocoat Epwp Epoflex 500 Proofseal Pt Proofseal Pu Epogrout Hs
Polar bear non-shrink grouting material is blended through a special procedure by specially selected cementations material, carefully selected fine aggregate and admixture. It owns the characteristics of high flow, non-shrinkage, early strength and high strength. Functionally they are divided into two categories include four products: high strength, extra early strength.
Concrete Admixtures Waterproofing Membranes Adhesives, Sealers, Toppings & Coatings
The Ground Granulated Blast Furnace Slag (GGBS/GGBFS) is a type of eco-friendly green building material and high quality secondary cementitious material for concrete and cement. It is recognized as one of the best secondary cementations material for building high durable concrete stricture in the world today! GGBS has taken over a top place of high-performance cement and concrete mineral additives with its unique characteristics of hydration, low-price raw material. GGBS is obtained by quenching molten iron blast furnace slag (a by-product of iron and steel making) in water or steam. It is then further grounded into the desired fineness in terms of the required particle size distribution. The main components of blast furnace slag are CaO (30-50%), SiO2 (28-38%), Al2O3 (8-24%), and MgO (1-18%). The other important aspect of GGBS is its superiority in concrete durability which extends the lifespan of buildings from fifty years to a hundred years. APPLICATIONS Soil stabilization Mortar Used in combination with Portland cement Pre-cast concrete Ready mix concrete Specialist projects
Aggregates are mixtures of sand, gravel, crushed rock or other bulk minerals used in construction, principally as a component of concrete, and in civil engineering. At CEMENTATION we supply aggregates for a range of core applications, from fill materials to aggregates that can be used in concrete, precast concrete, asphalt and for surface dressing. Aggregate plays an important role in concrete and construction part. We supply quality material which makes durable concrete with higher compressive strength and low permeability having better finish. We can supply a wide range of coarse, fine and blended aggregates in accordance with international standards. We acquire rock mines and stone crushing plants and enable us to fulfil contract of any size. Progressive stages if crushing and screening enable us to produce a range of aggregate sizes (06mm to 65mm) APPLICATIONS Road and Highway surfaces Constructions or Civil work Railway Ballast To make Concrete or Asphalt Filling
