In recent years, there has been significant increase in wind power generation capacity in India. We can supply different capacity wind turbines and related products. These are used for electricity generation and other purposes like pumping water, milling wheat etc For more details please contact us.
Name: Integral Steam Turbine Water Lubricated Pump(Energy Recovery-Turbine Pumps ) DESCRIPTION: The Pump is a single wheel steam turbine, two-stage pump, where both the turbine and impellers are mounted on a rigid shaft, supported by a central bearing assembly integral within a monobloc turbine/pump casing. This compact proven design will withstand water slugs in the steam line. It requires no external services or electrical supplies to operate and is one fifth the size of a conventional pump and turbine unit. The range is designed to ASME III Class 2 or 3 requirements. OPERATING LIMITS: Capacity up to 1550 m³ /h Head up to 4265m Discharge flange size 6 to 16 in Speeds 7500rpm Temperature up to 250°C APPLICATIONS: Auxiliary feedwater Reactor core isolation cooling Boiler feed Marine feed Safety related applications
Name: Integral Steam Turbine Water Lubricated Pump(Energy Recovery-Turbine Pumps ) DESCRIPTION: The Pump is a single wheel steam turbine, two-stage pump, where both the turbine and impellers are mounted on a rigid shaft, supported by a central bearing assembly integral within a monobloc turbine/pump casing. This compact proven design will withstand water slugs in the steam line. It requires no external services or electrical supplies to operate and is one fifth the size of a conventional pump and turbine unit. The range is designed to ASME III Class 2 or 3 requirements. OPERATING LIMITS: Capacity up to 1550 m³ /h Head up to 4265m Discharge flange size 6 to 16 in Speeds 7500rpm Temperature up to 250°C APPLICATIONS: Auxiliary feedwater Reactor core isolation cooling Boiler feed Marine feed Safety related applications
Water flow monitor LJZ-2 turbine parts Selection of advanced technology, absolutely first-class service quality, YOYIK over the years to the same faith. The main technical backbone are retired senior engineer, senior mechanic. Many of them have participated in the planning, production and installation of power stations such as Gezhouba, Ertan and Three Gorges, and provided high-quality equipment selection, construction planning, installation and dispensing of hundreds of hydropower stations and overhaul of thermal power plants. , After-sales service and other train services. Yoyik can offer many spare parts for power plants as below: #DF-Water flow monitor LJZ-2 turbine parts-DF Integrator Analog Input Board 421400688 Bolt electric heating rod ZJ-20-25 Eddy Current Signal Converter CON021/914-080 Speed sensor CS-1G-G-080-05-00 240v pressure switch BPSN4KB25XFSP12 Eddy Current Sensor PR6424/004-010 Speed sensor CS-1G-D-100-03-01 LVDT Sensor HBTD-6-800 Sensor DF310580-50-07-00 optical tachometer sensor SZCB-01 Casing Expansion Monitor DF9032 Max A Heat Expansion Transducer TD-2, RANGE: 50mm Power unit FDPC75C3-B linear differential sensor (Linear variable differential transformer) của van MSV 1000TD Equivalent Expanda Cable Coil for soot blower IK-530EL LVDT Sensor HY-6-100-15-D Heating rod DJ-18 Inverter AAD03020DKT01 Pressure relief valve YSF16-70/130KKJ tws proximity sensor CWY-DO-810800-50-09-02-01 linear sensor TDZ-1B-05 electromechanical pressure switch BPSN4KB25XFSP19 linear position control HL-3-250-15 Speed sensor CS-1G-D-065-02-00 Heat Expansion Sensor & Transmitter TD-2 0-50mm Switch 162F1300 Speed sensor CS-1G-G-080-03-01 Anti-interference relay UEG/F-8DPDT POSITIONER VALVE V18345-1010521001 INTERFACE BOARD EPSUPER-JKB-090214-A Speed probe CS-3F-M16 Bolt electric heating rod ZJ-22-5 Limit Switch WLGCA2-2-TH LVDT Sensor TD-1-0300-15-01 Bolt electric heating rod ZJ-20-39A Solenoid Valve 2W-160-15 Water flow monitor LJZ-2 turbine parts Water flow monitor LJZ-2 turbine parts MY-DFYL-2024-6-4
The Axial turbine is for low head power plants. Water flows axially into and out of the turbine. Axial flow turbines fall into two categories, fixed blade runner and variable pitch runner, also known as a Kaplan turbine. Fixed blade turbines are very well suited to low head power plants with limited variation in head and load. Its main advantage is its simple design. When operated at fixed speed, maximum efficiency is achieved at the design head and water flow. Kaplan turbines are used for medium to large power stations where there are large variations in the head, water flow and load. Its main advantage is its ability to adapt to variable conditions with a high efficiency. The variable pitch runner is mechanically more complex than a fixed pitch runner. Axial flow turbines can be supplied for a head of 2m to 70 m. The runner diameter is available from 0.6 m to 5 m. Power capacity is from 55 kW to 50 MW.
The tubular turbine is an axial flow turbine, in a straight or S-shaped configuration. A Tubular Turbine can be supplied for a head of 2 m to 30 m. The runner diameter is available from 0.8 m to 5.6 m. Power capacity is from 250 kW to 15 MW. This turbine has high efficiency and lower constructon cost.
Pelton turbine The runner has bucket shaped blades on the periphery. The jet of water is tangential to the runner. The characteristics are, high head applications, a simple design, few problems with cavitation, highly cost effective. Pelton turbines can be supplied for a head of 100m to 500 m. The runner diameter is available from 0.55 m to 1.5 m. Power capacity is from 200 kW to 10 MW. Inclined jet turbine: The water flows into and out of the runner at an angle to the main shaft. The characteristics are high efficiency over a wide range of water flow, more flexible installation options, somewhat more complex than a Pelton turbine. Inclined jet turbines can be supplied for a head of 60m to 300 m. The runner diameter is available from 0.32 m to 0.8 m. Power capacity is from 55 kW to 6.3 MW.
In a Francis turbine, the water flows radially into the turbine and axially out of the runner. The Francis turbine, invented by an American engineer in 1849, is the most widely deployed modern turbine. The main characteristics of the Francis turbine are - a wide range of water head, simple and reliable structure, and high efficiency. A Francis Turbine can be supplied for a head of 15 m to 250 m. The runner diameter is available from 0.4 m to 4.5 m. Power capacity is from 75 kW to 50 MW. New style francis turbine, compared to the old one, it has the advantages of convenient installation, high efficiency, low noise and compact structure.
TRANSFORMER : ALL TYPE : Dry Type/Air Cooled, Oil Cooled, Water. We can supply small transformer from 33kV and up to 54000kVA or more. For more details please contact us.
