Single Sphere Rubber Expansion Joint Features: -Allow for 4 way movements -Precision molded of synthetic rubber&nylon -Excellent ability to absorb vibration and sound -Perfect corrosion resistant -Using floating flange,easy to install Rubber Expansion Joint EPDM,NBR,NR, CSM,VITON,SILICON. Size:Size: DN32-DN3000 Pressure: PN10,PN16,PN25 End Flange:DIN2501, BS EN1092, BS4504PN16,JIS10K,ANSIB16.5 Flange
Single Arch Rubber Expansion Joint Features: -Working pressure ratings up to 150 psi,Temperature ratings to 250°F -Vacuum ratings to 15 in.Hg -Allows for greater motion capabilities than general expansion joint -Excellent for absorbing thermal expansion,eliminating vibration&sound -Gaskets and packing not required -Absorbs water puisation and protects against start-up surge force Rubber Expansion Joint EPDM,NBR,NR, CSM,VITON,SILICON. Size:Size: DN32-DN3000 Pressure: PN10,PN16,PN25 Pressure Test: 15Bar, 24Bar,37.5Bar.
Ductile Iron GGG50,GJS500-7,GGG40 Size: DN40-DN600 Pressure: PN10;PN16; 230psi. Pressure Test: PN15,PN24,350psi. EPDM, NBR Rubber Seals to EN681 & ASTM D2000. Painting: RAL5017 FBE coated, Min., Coating Thickness 200m. Connected Pipe: DI Pipe, PVC/UPVC Pipe, Steel Pipe and Part AC Pipe.
Ductile Iron GGG50,GJS500-7,GGG40 Size: DN40-DN600 Pressure: PN10;PN16; 230PSI. Pressure Test: PN15,PN24,350PSI. EPDM, NBR Rubber Seals to EN681 & ASTM D2000. Painting: RAL5017 FBE coated, Min., Coating Thickness 200m. Connected Pipe: DI Pipe, PVC/UPVC Pipe, Steel Pipe and Part AC Pipe.
Ductile Iron GGG50,GJS500-7,GGG40 Size: DN40-DN2000 Pressure: PN10,PN16,PN25,PN40,230psi Pressure Test: 15Bar, 24Bar, 37.5Bar, 350psi EPDM, NBR Rubber Seals to EN681 & ASTM D2000. Painting: RAL5017 FBE coated, Min., Coating Thickness 200m. Connected Pipe: DI Pipe, PVC/UPVC Pipe, Steel Pipe and Part AC Pipe.
Ductile Iron GGG50,GJS500-7,GGG40 Size: DN40-DN2000 Pressure: PN10,PN16,PN25,PN40,230psi Pressure Test: 15Bar, 24Bar, 37.5Bar, 350psi EPDM, NBR Rubber Seals to EN681 & ASTM D2000. Painting: RAL5017 FBE coated, Min., Coating Thickness 200m. Connected Pipe: DI Pipe, PVC/UPVC Pipe, Steel Pipe and Part AC Pipe.
Ductile Iron GGG50,GJS500-7,GGG40 Size: DN40-DN2000 Pressure: PN10,PN16,PN25,PN40,230psi Pressure Test: 15Bar, 24Bar, 37.5Bar, 350psi EPDM, NBR Rubber Seals to EN681 & ASTM D2000. Painting: RAL5017 FBE coated, Min., Coating Thickness 200m. Connected Pipe: DI Pipe, PVC/UPVC Pipe, Steel Pipe and Part AC Pipe.
Supplier: Chemical, chemical raw material, auxiliaries, solvents, paint, textile fiber, rubber, plastic, paint drier, plasticizer, flame retardant, surfactant, additives, steel pipe, steel tube, stainless steel tube, stainless steel pipe, ms pipe, pipe fitting, flange, fasteners, steel wire
Services: Transportation agent,customs clearance service,
Buyer: Import chemical raw materials, auxiliaries, bulk commodities
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
