Product Introduction PET spunbond substrate fabric compared with short fiber polyester tire has high tensile strength, elongation, stability, aging resistance, long service life, good wettability and other characteristics, as the internationally recognized high-performance SBS, APP and other modified asphalt waterproof roll tire. Application Area Modified asphalt waterproof coil is widely used in waterproof concrete building, such as building roof, underground structure, high-speed railway, tunnel, highway and railway bridge waterproof field.
The polyester staple fiber machine (PSF plant) takes virgin PET Chips, recycled Bottle Flakes, Popcorn and Lumps, etc., as raw material, with continuous drying (or batch drying through Vacuum Dryer), high pressure melt spinning process engineering and VFD controlled Spinning & Stretching process engineering to produce normal Staple Fibre, High Tenacity Low Elongation Staple Fibre and Hollow Fibre. Single plant capacity is 15T.P.D. to 80T.P.D. Equipment Technical Data Titer Range dtex 6.67-16.67 Spinning Pos. nos. 6-24 Spinning Pitch mm 700, 750 Plant Capacity TPD 15-80 Spinneret dia. mm 328, 358, 410 Spinning Mechanical Speed m/min 500-1,500 Spinning Processing Speed m/min 500-1,300 Stretching Mechanical Speed m/min 240 Stretching Processing Speed m/min 230 Total Tow Titer at Stretching dtex 600,000-3,000,000 Stuffer Box Width mm 160-410 Cutting Length mm 25, 32, 38, 44, 51, 64, 76, 101 Bale Weight kg 200-350 Application: Cushions Pillows Quilts Toys Jacket Mattress Non woven carpet Automotive felts, speaker felts, geo textiles, polyfill wadding, filter fabrics and other acoustics as well. Spinning Line: Continuous Dryer Hopper Screw Extruder Polymer Pipe Filter Spin Beam (Meter Pump System, Spin Pack, Spinneret) Quenching Unit Interfloor Duct Draw-off Wall Capstan Roller Sunflower Gearing Unit Automatic Fiber Can Device Drawing line: Can Creel Inlet Thread Guide Tow Guide Stand Dipping Bath 1st Draw Stand Draw Bath 2nd Draw Stand Draw Steam Chest 3rd Draw Stand Tow Stacker Crimper Steam Box Crimper Silicone Oil Sprayer Machine Tow Tension Stand Cutter Fiber Spreading Machine Relaxer Fiber Blowing system Baling Press
Supplier: Diesel oil en 590 10 ppm & other grades, food stuff, textiles, gloves, masks, waste management machineries & plants, metal scrap, chemicals, water treatment plants, sewage treatment plants, waste water treatment plants, filtration systems, waste to energy plants, msw, e waste, metal recycling, lithium ion recycling, plastic waste to energy, tyre recycling, bio gas, biodiesel, diesel blending plants, waste sludge recycling,, waste heat recovery boilers
Pipe marking line is extruded by smaller single screw extruder through the composited extrusion die. Vacuum calibration water tank: it is equipped with two-stage vacuum system(for large diameter)advanced water recycle & high pressure cooling system, vacuum degree adjustment device and accurate water level & water temperature automatical control system. The accurate stannum bronze calibratation sleeve ensures fast cooling speed and molding of pipe. Its material is stainless steel. Spray cooling water tank: Long cooling unit ensures high efficiency cooling, Unique pipeline design shorten cooling length, its material is stainless steel. Haul-off unit: special integral transmission unit avoids asynchrony of individual transmission, Various control method ensures more flexible & accurate orientation, Accurate pressure regulating system makes hauling power adjustable. It has unique structure & flexible operation, its speed can be adjusted by motor inverter. Cutting unit: Full-hydraulic design of cutting unit ensures flexible pressure in state of cutting pipes, Flexible adjust for saw position & cutting depth, Unique power input system ensures high reliability of planetary unit, With ultra silent & enforced sucking system, Unique non-scrap cutting unit enusre clean cutting section for 16mm to 315mm pipe. Control system: Adopts the one of the most advanced plastic extrusion machinery control systems----PLC. It can ensure much higher quality extrusion, PLC system ensures high speed and convenient internet function that much more accurate and flexible control, intelligentized control order make the operation more simple. Packing in film or according to your needs.
wood plastic extrusion line(wpc machine) can make different kinds of pvc wpc and pe wpc products,such as WPC Plank plate,Guard rail profile, WPC floor. capacity:50-500kg/h material: SS304 electric: ABB,SIEMENS,OMRON SCHNEIDER flow: wpc shredder&crusher-wood power milling machine-wood powder drier-wpc mixer-wpc granulator-wpc extruder- surface treatment(embossing,sanding,brushing)
The complete extrusion line is developed with the 1990s advanced technology of west europe by our company. The main machine is single screw extruder with cossponding downstream equipment. The main technique parameter Wooden pallet and fixed in container
Monoblock pumps - Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features - High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Inbuilt thermal overload protector in al single phase pumpsets upto 2.0 HP - Specially designed for wide voltage operation - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life - Back pull-out design for easy servicing and repair - Double shielded ball bearings, so no need of external lubrication - All Model fitted to Mechanical seal. specification - Power Range : 0.37Kw - 1.5 Kw (0.5 HP - 2.0 HP) - Version : Single Phase, 220-240V, 50Hz AC Supply Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 32 Mtr. - Maximum Flow Rate : 940 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Mechanical Seal - Type of Duty : S1 (Continuous) - Method of Starting : Permanent Split Capacitor (PSC) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 25 X 25, 32 X 25, 40 X 32, 40 X 40, 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 (All size in mm) characteristics of clear cold water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Mechanical Seal : Carbon & Ceramic Motor Shaft : EN-8 Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Plastic
Falcon regenerative monoset pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. Salient Features High operating efficiency resulting in lower power consumption. - Good suction lift characteristics. - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. - All Model fitted to Mechanical seal. specification Power Range : 0.37 Kw - 0.75 Kw (0.5 HP - 1.0 HP) - Version : Single Phase, 220-240V, 50Hz AC Supply - Speed : 1440 RPM - Maximum Total Head : 18 Mtr. - Maximum Flow Rate : 4200 LPH - Maximum Suction Lift : 8 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Mechanical Seal - Type of Duty : S1 (Continuous) - Direction of Rotation : Single Phase, Clockwise from driving end - Nominal Pumpset Size (Suction X Delivery) : 25mm X 25mm Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 material Of construction - Motor Part Name Material Mechanical Seal : Carbon & Ceramic Motor Shaft : SS-410 Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : Brass Cooling Fan : Plastic
PVC/CPVC plastic pipe extrusion line Standard export packaging
1. Model SJZ series conical twin screw extruder is a kind of special equipment for extruding PVC compound.With different kinds of molds and auxiliary machines, it can produce all sorts of PVC plastic pipe, profile, plate material, sheet material, bar material and granulation. 2. The conical twin screws have applied oil cooling system. Barrel is cooled by special wind cooling system. 3. The conical twin screw extruder system has applied special computer control. According to customers requirements, most reasonable structure of conical twin screw can be made so as to achieve best plasticity performance and material quality. 4. The conical twin screw is made by high precision special digital screw miller; extruding property can be highly harmonized. It has firstly introduced advanced technique of producing screw with variable pitch and depth, so that the material can be more softly sheared and cut. 5. The distribution box is specially designed, pull force bearing is fully imported, and the drive life span can be prolonged. It can bear larger extruding pressure 6. The electrical system has mainly applied imported parts, it has multiple alarm system, and there are few problems which can be easily eliminated. The cooling system has applied special design, heat emission area is enlarged, the cooling is rapid, and temperature control tolerance can be 1degree.
