JESSIN ROCK DRILL CO.,LIMITED, www.dthhammer-js.com PDC drill bits use PDCs as main cutting media, with the excellent wear-ability and impact toughness of the PDC. It has a long service life, high-efficiency, and good cost performance. PDC bit is mainly used for drilling soft and medium hard rock, and it must work under low drilling pressure, mid-low speed and big drainage. JESSIN can supply all kinds of PDC core and non-core bits, PDC sintering matrix bits and PDC anchor bits. PDC bit can be widely used in the fields of geological exploration, coal mining, water conservancy and hydropower, construction of road and railway. We also can design PDC bits according to customer requirements, such as different geology conditions, special strata and so on. Features 1. Super long service life. The service life of PDC bit is as much as 4~5 times than diamond bit, at least 10 times than tungsten carbide bit. 2. High drilling speed. 3. Can be operated with low pressure and speed. 4.Has a good gage protection. 5.Used widely, more suitable for drilling in the stratum with hardness coefficient f
Supply Atlas Copco spare parts by JESSIN ROCK DRILL CO.,LIMITED 3115132400 Diaphragm 3115145700 Side Bolt 3115147600 Seal 3115295000 Front Head 3115296500 Sleeve 3115296890 Conversion Kit 3115297300 Piston Guide 3115298800 O Ring 3115211300 Bolt 3115211301 Bolt 3115211900 Guide 3115212100 Flushing Head 3115264980 Gear 3115504000 Side Bolt 3115504300 Connect Plate 3115504310 Connect Plate 3115504312 Connect Plate 3115504501 Guide 3115505910 Segregator 3115515200 Water Pressure Plate 3115531400 Copper Sleeve 3115915091 O Ring Kit 3115915095 Seal Kit 3115915096 Seal Kit 3115915097 Seal Kit 3115915099 Seal Kit 3115915390 O Ring Kit 3115915392 Seal Kit 3115915500 Spare Part 3115915590 O Ring Kit 3115915890 Seal Kit 3115915893 Hex Repair Kit 3115914990 Seal Kit 3115916995 Seal Kit 3115916590 Seal Kit 3115916690 Seal Kit 3115916290 Seal Kit 3115916390 Seal Kit 3115901164 Seal Kit 665100012 Cup Seal 3115238200 Damping Piston 3115238500 Cup Seal 3115238600 Cup Seal 3115238700 Cup Seal 3128309734 Manipulator Arm 3128310378 Jaw 3128310422 Bushing Half 3128306383 Large Expanding Shaft 3128306256 Hose Holder 3128003155 Large Expanding Shaft 3128310598 Medium Expanding Shaft 3128310472 Small Expanding Shaft 3128309396 Expanding Shaft 3128310453 Large Expanding Shaft Copper Sleeve 3128310613 Medium Expanding Shaft Copper Sleeve 3128313405 Small Expanding Shaft Copper Sleeve 3128301389 Piston Rod End 3128302270 Drill Rod Clamp Bushing 3128008300 Holder 3128008200 Holder 3128304355 Sliding Piece 3128312307 Holder 3128312308 Holder 3128003401 Sliding Bar 3128309562 Rock Drill Base Plate 3128310520 Rock Drill Base Plate 3128003700 Rock Drill Buffer Block 3128217400 Rock Drill Protection Cover 3128216900 Bushing Segment 3128216600 Seal 3128003137 Manipulator Shaft 3128310390 Manipulator Shaft 3128309736 Manipulator Mounting Seat 3128003114 Vertical Shaft Bearing Seat 3128310398 Arm 3128001860 Front Fixed Plate 3128301306 Dr. St. Su. House 3128303921 Middle Plate 3128309793 Middle Plate 3128310734 Slag Back Plate 9111408850 Link Arm 4350265028 End Piece 4350265008 Adapter 4350265006 Housing 4350265041 Adapter 4350265045 Sealing Bush 4350265047 Sealing Bush 4350265105 Gear Wheel 4350258430 Repair Kit 4350258450 Repair Kit 502109194 Link Arm Bearing 544215300 Grease Nipple 544216200 Lubricating Nipple 544256200 Grease Nipple 3128003116 Spacer Ring 501000016 Bearing 501000051 Bearing 501000072 Bearing 501001901 Bearing 501001900 Bearing 509022200 Bearing 516150401 Bearing 516153800 Bearing 3128310213 Bushing
Established in 2005,JESSIN ROCK DRILL CO.,LIMITED is a professional manufacturer of rock drilling tools. PRODUCTSYour present positionï¼?Home> PRODUCTS>DTH Bits DTH Bits (1) Made of premium quality nickel-alloy steel 23CrNi3MoA for increased durability and wear characteristics, and YK 05 tungsten carbide as same grade as internationally well-known T6 brand. (2) Apply "hot (thermal) -insertion" processing procedure to insert the buttons as same as internationally well-known brand, (3) Entire CNC processing procedure ensure the quality consistency and reliable. (4) Military grade requirements of heat-treatment guarantee durability, Specific heat treatment standards and special â??stress reliefâ?? processes ensure consistent performance. (5) Designed for maximum performance and hole cleaning ability and high penetration rate.Our bits are interchangeable with Atlas Copcoâ??s COP32 34 44 54 64 84, Ingersoll-Rand â??s DHD3.5,DHD3.5HD, DHD 340A , DHD350R, DHD 360, Mission60, DHD380 QL40, QL50 , QL60, QL80.SD10, NUMA100, NUMA120,ect. (6) Matching the insert to the job requirements is essential in achieving the desired results. Each of the following buttons is ideal for different ground conditions, abrasion levels, PSIs and penetration levels. In general, the larger the number of gauge buttons the better overall performance, especially in hard rock. (7) Specification of dth hammer button bits:Diameter: (mm)1-2 inch low air pressure DTH bits Shank: BR1, BR2, DHD2.5 57/64/70/76/80/82/90mm (8) 3 inch high Air pressure DHT bits Shank: BR3,DHD3.5,COP34,COP32,QL30,M30,IR3.5 85 / 90 / 95 / 100 / 105/110mm (9) 4 inch high Air pressure DHT bits Shank:DHD340,COP44,M40,SD4,QL40 105 / 110 / 115 / 120 / 127/130mm (10) 5 inch high Air pressure DHT bits Shank:DHD350,COP54,M50,SD5,QL50 133 / 140 / 146 / 152 / 165mm (11) 6 inch high Air pressure DHT bits Shank:DHD360,M60,SD6,QL60,COP64 152 / 165 / 178 / 190 / 203mm (12) 8 inch high Air pressure DHT bits Shank:DHD380,COP84,M80,SD8,QL80 195 / 203 / 216 / 254 / 305mm (13) 10 inch high Air pressure DTH bits Shank:SD10, NUMA100 254/270/279/295/305mm (14) 12 inch high Air pressure DTH bits Shank:SD12,DHD1120,NUMA120,NUMA125 305/330/343/356/368/381mm (15) 15 inch high Air pressure DTH bits Shank: DHD1150, SD15,NUMA125 381/391/435/457/483/503mm (16) Over 20 inch high Air Pressure DTH bits Shank: NUMA180,NUMA240,483/508/560/578/610/660mm
Model specification: DHD3.5, DHD340,DHD350,DHD360,DHD380,DHD112, (7) Specification of dth hammer button bits:Diameter: (mm)1-2 inch low air pressure DTH Shank: BR1, BR2, DHD2.5 57/64/70/76/80/82/90mm (8) 3 inch high Air pressure DHT Shank: BR3,DHD3.5,COP34,COP32,QL30,M30,IR3.5 85 / 90 / 95 / 100 / 105/110mm (9) 4 inch high Air pressure DHT Shank:DHD340,COP44,M40,SD4,QL40 105 / 110 / 115 / 120 / 127/130mm (10) 5 inch high Air pressure DHT Shank:DHD350,COP54,M50,SD5,QL50 133 / 140 / 146 / 152 / 165mm (11) 6 inch high Air pressure DHT Shank:DHD360,M60,SD6,QL60,COP64 152 / 165 / 178 / 190 / 203mm (12) 8 inch high Air pressure DHT Shank:DHD380,COP84,M80,SD8,QL80 195 / 203 / 216 / 254 / 305mm (13) 10 inch high Air pressure DTH Shank:SD10, NUMA100 254/270/279/295/305mm (14) 12 inch high Air pressure DTH Shank:SD12,DHD1120,NUMA120,NUMA125 305/330/343/356/368/381mm (15) 15 inch high Air pressure DTH bits Shank: DHD1150, SD15,NUMA125 381/391/435/457/483/503mm (16) Over 20 inch high Air Pressure DTH bits Shank: NUMA180,NUMA240,483/508/560/578/610/660mm Top sub connection: API 2 3/8" Reg Chuck connection configuration: IR3.5 Available bit size/mm: 90-115 Length(without bit)/mm: 888 Outside diameter/mm: 82 Net weight(without bit)/kg: 25 Impact rate : At 1.5Mpa,25HZ Recommended rotation speed: 25-40r/min Air consumption, CFM& (M3/min) Work Pressure 1MPa 3.8m3/min 1.5MPa 7.5m3/min 1.8MPa 2.4MPa.
Korean made high quality Spare Parts for Rock Drill Machine We are a specialist for drilling and blasting business in South Korea. - We are covering world leading brands - Genuine Spare Parts - High quality Korean made alternative spare parts - Fully reconditioned machine & parts are available ATLAS COPCO Jumbo Drill : BOOMER 104, BOOMER 132, BOOMER 281, BOOMER 282, BOOMER H227, BOOMER H210, BOOMER H245, BOOMER 352, BOOMER 353, BOOMER S1 D, BOOMER S1 L, BOOMER E1 C, BOOMER L1 C, BOOMER L1C DH, BOOMER E1 C DH, BOOMER M2 C, BOOMER E2 C, BOOMER L2 D, BOOMER L2 C, BOOMER L3 C, BOOMER WL3 C, BOOMER XL3 C Hydraulic Drill : ROC F11, ROC F9, ROC L8, ROC D9, ROC D7, ROC D5, ROC D3, ROC 812, ROC 748, ROC 742, ROC 612 Drifter : COP 131, COP 1640, COP 1032, COP 1038, COP 1238, COP 1440, COP 1638, COP 1838, COP 1840, COP 1850, COP 2160, COP 2238, COP 2550, COP 2560, COP 3038, COP 4050 INGERSOLL RAND Hydraulic Drill : CDH 701, CDH 712, CDH 812, CDH 901, LME 401, LM 401, LM 470, LM 500, LM 600, CM470, CM 580, ECM 470, ECM 580, ECM 590 Pneumatic Drill : LM 100, ECM 345, ECM 350, ECM 351 Drifter : YD 90, VL 120, VL 140, YH 45, YH 50, YH 55, YH 60, YH65, YH 70, YH 80, YH 100, YH 200 SANDVIK TAMROCK Hydraulic Drill : COMMANDO 100, COMMANDO 300, CHA 500, CHA 600, CHA 660, CHA 1000, CHA 1100, RANGER 500, RANGER 700, RANGER K5 Drifter : HL 300, HL 500, HL 510, HL 550, HL 560, HL 600, HL 700, HL 1000 TOYO Hydraulic Drill : THCD 550, THCD 650, THCD 656, TCD 915, TCD 918, TCD 928, TCD 1218, TCD 1229 Jack Hammer : TY 24 C, TY 24 LD Drifter : TH 500, TH 501, TH 800, TH 850 FURUKAWA Jumbo Drill : JTH2A 90, JTH2RS 90E, JTH2A 90E, JTH2RS 150E, JTH2RS 190EX, JTH2RS 190EX L, JTH3RS 150, JTH3RS 150E, JTH3RS 150 R, JTH3RS 190EX, JTH3RS 190EX M, JTH2200R L, JTH3200R L Hydraulic Drill : HCR C300S, HCR 300, HCR C500, HCR 500S, HCR 9, HCR 9 DS, HCR 12, HCR 12 DS, HCR 15 EDS, HCR 10 DS, HCR 900, HCR 1200, HCR 1500 Pneumatic Drill : PCR 200, PCR 200 DTH Drifter : PD 200, HD 300S, HD 300, HD 500, HD 609, HD 612, HD 615, HD 709, HD 712, HD 715, HD 75, HD 150, HD 190, HD 210 JUNJIN & SOOSAN Hydraulic Drill : SHCD 650, SD 700, SD 1000, STD 11, STD 11T, STD 14E, JD 800, JD 800 K, JD 800 E, JD 1300 E, JD 1400 E, JD 1500 E, JD 1500 L Drifter : SP 3, SP 6, JET 7, JET 8, JET 9, TD 45, TD 45T, TD 51, TD 51W
Korean made Pneumatic Crawler Drill for Top Hammer & DTH drilling both way We are a specialist for drilling and blasting business in South Korea. - We are covering world leading brands - Genuine Spare Parts - High quality Korean made alternative spare parts - Fully reconditioned machine & parts are available ATLAS COPCO Jumbo Drill : BOOMER 104, BOOMER 132, BOOMER 281, BOOMER 282, BOOMER H227, BOOMER H210, BOOMER H245, BOOMER 352, BOOMER 353, BOOMER S1 D, BOOMER S1 L, BOOMER E1 C, BOOMER L1 C, BOOMER L1C DH, BOOMER E1 C DH, BOOMER M2 C, BOOMER E2 C, BOOMER L2 D, BOOMER L2 C, BOOMER L3 C, BOOMER WL3 C, BOOMER XL3 C Hydraulic Drill : ROC F11, ROC F9, ROC L8, ROC D9, ROC D7, ROC D5, ROC D3, ROC 812, ROC 748, ROC 742, ROC 612 Drifter : COP 131, COP 1640, COP 1032, COP 1038, COP 1238, COP 1440, COP 1638, COP 1838, COP 1840, COP 1850, COP 2160, COP 2238, COP 2550, COP 2560, COP 3038, COP 4050 INGERSOLL RAND Hydraulic Drill : CDH 701, CDH 712, CDH 812, CDH 901, LME 401, LM 401, LM 470, LM 500, LM 600, CM470, CM 580, ECM 470, ECM 580, ECM 590 Pneumatic Drill : LM 100, ECM 345, ECM 350, ECM 351 Drifter : YD 90, VL 120, VL 140, YH 45, YH 50, YH 55, YH 60, YH65, YH 70, YH 80, YH 100, YH 200 SANDVIK TAMROCK Hydraulic Drill : COMMANDO 100, COMMANDO 300, CHA 500, CHA 600, CHA 660, CHA 1000, CHA 1100, RANGER 500, RANGER 700, RANGER K5 Drifter : HL 300, HL 500, HL 510, HL 550, HL 560, HL 600, HL 700, HL 1000 TOYO Hydraulic Drill : THCD 550, THCD 650, THCD 656, TCD 915, TCD 918, TCD 928, TCD 1218, TCD 1229 Jack Hammer : TY 24 C, TY 24 LD Drifter : TH 500, TH 501, TH 800, TH 850 FURUKAWA Jumbo Drill : JTH2A 90, JTH2RS 90E, JTH2A 90E, JTH2RS 150E, JTH2RS 190EX, JTH2RS 190EX L, JTH3RS 150, JTH3RS 150E, JTH3RS 150 R, JTH3RS 190EX, JTH3RS 190EX M, JTH2200R L, JTH3200R L Hydraulic Drill : HCR C300S, HCR 300, HCR C500, HCR 500S, HCR 9, HCR 9 DS, HCR 12, HCR 12 DS, HCR 15 EDS, HCR 10 DS, HCR 900, HCR 1200, HCR 1500 Pneumatic Drill : PCR 200, PCR 200 DTH Drifter : PD 200, HD 300S, HD 300, HD 500, HD 609, HD 612, HD 615, HD 709, HD 712, HD 715, HD 75, HD 150, HD 190, HD 210 JUNJIN & SOOSAN Hydraulic Drill : SHCD 650, SD 700, SD 1000, STD 11, STD 11T, STD 14E, JD 800, JD 800 K, JD 800 E, JD 1300 E, JD 1400 E, JD 1500 E, JD 1500 L Drifter : SP 3, SP 6, JET 7, JET 8, JET 9, TD 45, TD 45T, TD 51, TD 51W and many other machines
T45 89mm button bits are suitable for powerful percussive drills and top hammers with high speed drifter, such as atlas copco 282 rocket boomer, atlas copco 352 rocket boomer jumbo, atlas copco d7roc, furukawa hcr 1200, tamrock, and ingesoll rand ecm660, the products are widely used in bench and production drilling, extensional drilling, our products with comparative advantages of the more prominent cost-effective as the famous brand in the world, our products have been recognized as high-quality brand of rock-drilling tools made in china. Drill bit | broca | broca | foret | bohrer | matkap ucu | punta da trapano | poranterä | borr | boret | jesie | druil giotán
The supanchor self-drilling anchor Is a unique anchoring system and is today Answer to the increasing demands of the Tunnelling industry and ground engineering for safer and faster production. The system provides advantages for all areas of its Applications, where boreholes would require the Time consuming drilling with casing systems in Unconsolidated or cohesive soil. Features and advantages Fits supanchor standard boomer, roc and Mustang rigs. Particulary suitable for difficult ground conditions. A high rate of installation since drilling, placing And grouting can be performed in one single Operation. Self drilling system eliminates the requirement For a cased borehole. Installation with simultaneous drilling and Grouting possible. Easy installation in all directions, also upwards. Suitable for working in limited space, height and In areas of difficult access. Simple post grouting system. Hot-dipped galvanizing for corrosion protection Applications Tunnelling ground engineering Radial bolting slope stabilization Forepoling micro injection pile Face stabilization temporary support anchor Portal preparation soil nailing.
The SupAnchor Self-Drilling Anchor is a unique anchoring system and is todayÂë answer to the increasing demands of the tunnelling industry and ground engineering for safer and faster production. The system provides advantages for all areas of its applications, where boreholes would require the time consuming drilling with casing systems in unconsolidated or cohesive soil. Features and Advantages Fits SupAnchor standard Boomer, ROC and Mustang rigs. Particulary suitable for difficult ground conditions. A high rate of installation since drilling, placing and grouting can be performed in one single operation. Self drilling system eliminates the requirement for a cased borehole. Installation with simultaneous drilling and grouting possible. Easy installation in all directions, also upwards. Suitable for working in limited space, height and in areas of difficult access. Simple post grouting system. Hot-dipped galvanizing for corrosion protection Applications Tunnelling Ground engineering Radial bolting Slope stabilization Forepoling Micro injection pile Face stabilization Temporary support anchor Portal preparation Soil nailing SupAnchor Rock Reinforcement Specifications TECHNICAL DATA R 32N R 32S Outside diameter.............................................. 32 mm Internal diameter, average................................ 18.5 mm External diameter, effective............................. 29.1 mm Effective cross sectional area, average............ 396 mm Ultimate load capacity...................................... 280 kN Yield load capacity............................................ 230 kN Average tensile strength, Rm........................... 720 N/mm Average yield strength, Rp0,2.......................... 560 N/mm GENERAL DATA Type of steel............................................. EN 10083-1 Thread type............................................... R32. ISO 10208
