DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
PET Roll Clear Color Plastic Scrap For Sales MATERIAL : PET Roll Clear Color CATEGORY : PET TYPE : Roll GRADE : Clear Color SPECIFICATION : "Length 3 meter, Diameter 30-50 cm Weight of each Roll: 500-700 kgs The Film Thickness is 23 to 70 micron. Load: 50-54 rolls each 40ft HC container. Deduct 20kg of paper core for each roll" ORIGIN : Germany LOADING WEIGHT : 26 Tons FAS (USD/Ton) : 450-600
About THE Product : Blast furnace slag is used in the production of cement (iron Portland and blast furnace cement). Air-cooled blast furnace slag is formed by allowing the molten slag to cool relatively slowly under ambient conditions; final cooling can be accelerated with a water spray. The cooled material is hard and dense, although it can have a vesicular texture with closed pores. After crushing and screening, air-cooled slag can be used in several applications. Granulated slag is formed by quenching molten slag in water to form sand-sized particles of glass. The disordered structure of this glass gives the material moderate hydraulic cementitious properties when very finely ground into granulated blast furnace slag, but if it can access free lime, the granulated blast furnace slag develops strong hydraulic cementitious properties. Pelletized or expanded slag is cooled through a water jet, which leads to rapid steam generation and the development of innumerable vesicles within the slag. The vesicular texture reduces the overall density of the slag and allows for good mechanical binding with hydraulic cement paste. Blast Furance Slag is a nonmetallic co-product which is produced in the process of iron manufacturing, Granulated Blast Furnace Slag is a glassy granular material formed when molten blast furnace slag is rapidly cooled by direct water. Rapid cooling prohibits the formation of crystals and forms glassy, non-metallic, silicates and alumino silicates of calcium. GBFS : (Granulated Blast Furnace Slag) Source : Granulated BF Slag From Gujarat State, India Supply Quantity : 50,000 Metric Tons Per Month Packing: Bulk Parameters (% BY MASS) CaO 30-38 Al2O3 15-20 SiO2 30-40 Glass Content 85-97 MgO 8-11 Fe2O3 0.5-1.5 Moisture 10 MAX Size -5mm Min 95, +5 mm Max 5 Relative Gravity 2.9 Bulk Density(Bagged) 1200 KG/M3
We Are Indonesia MDF Board MANUFACTURER ## Made from Mix Hardwood Fiber ## Density 720kg-800kg ## Flat and smooth surfaces by well sanded ## Sanding paper number 240 ### High density ***** Usage Furniture components - Decoration ## Housing components ## All sizes available ## Special required sizes can be made ## MOQ 24 cbm in 20ft ## Price range depend on sizes from usd 150/cbm - usd 230/cbm FOB Indonesia main port ## Payment term by Bank transfer 30% Deposit and 70% balance agaist copy of BL only , No L/C accepted due to high Banking cost
MDF Board ***** Flatt and Smooth surfaces by well sanded ***** made from Mix hardwood Fiber *** High Density vary from 760kg - 820kg /m3 depend on thickness *** All sizes available by demand *** usage : Housing components - Furniture components - Carving purposes **** MOQ 40 cbm in 40ft *** Payment term only by 30% Deposit and 70% balance against copy of B/L after shipment released *** No L/C accepted due to high Banking fee & Complicated procedures - For saving your time , Please dont send any inquiry for L/C payment
Indonesia Plywood Factory supply : ***** 2025 Meranti Commercial Plywood ***** Usage : Multi Purposes = Furniture and Housing components **** All Sizes available ***** Face/ Back Red Meranti Veneer ***** Smooth and Flta Surfaces by well sanded ***** Meranti Hardwood Core - high density ***** All Type of Glue available ***** MOQ = 48 cbm in 18 Carton Boxes ***** Payment term by Bank Transfer and will discus with buyer ***** Delivery : Refer to buyer schedule ***** Payment term simply by Bank TT 30% up front and 70% balance against copy of Bl after vessel departed
Indonesia Origin MDF Manufacturer and Exporter ***** MDF Board Thickness from 2mm t0 25mm x 1220mm x 2440mm 0r 1830mmx3660mm ***** Flatt and Smooth surfaces by well sanded ***** made from Mix hardwood Fiber *** High Density vary from 720kg - 820kg /m3 depend on thickness *** All sizes available by demand *** also available Melamine face MDF ***** usage : Housing components - Furniture components - Carving purposes **** MOQ 48 cbm in 40ft *** Payment term only by 30% Deposit and 70% balance against copy of B/L after shipment released *** No L/C accepted due to high Banking fee & Complicated procedures
MDF Board ***** Flatt and Smooth surfaces by well sanded *****or MDF Melamine faced ***** Core made from Mix hardwood Fiber *** High Density vary from 720kg - 820kg /m3 depend on thickness *** All sizes available by demand *** usage : Housing components - Furniture components - Carving purposes **** MOQ 40 m3 in 40ft *** Payment term only by 30% Deposit and 70% balance against copy of B/L after shipment released *** or 50% Deposit and 50% Balance after received container in buyer ware house and checking quality ***** No L/C accepted due to high Banking fee & Complicated procedures
MDF Board ***** Flatt and Smooth surfaces by well sanded ***** made from Mix hardwood Fiber *** High Density vary from 760kg - 820kg /m3 depend on thickness *** All sizes available by demand *** Price depend on sizes starting from usd 6.40 / pc (FOB) ***** usage : Housing components - Furniture components - Carving purposes **** MOQ 48 cbm in 40ft *** Payment term only by 30% Deposit and 70% balance against copy of B/L after shipment released **** Or Special Payment term to check quality : 50% Deposit Bank TT in advance and 50% Balance after received cargo and inspect the quality ***** No L/C accepted due to high Banking fee & Complicated procedures
Applications: Use to manufacture gypsum panel or building plasters Use to make gypsum mold or statutes As grout of marble, clay and ceiling tiles As a color additive Act as additive to other products Types: 1. Super Micronized Gypsum Powder 2. Facade Rendering Gypsum Packaging: 25 kg per bag 30 kg per bag 50 kg per bag 1 ton jumbo bag 1.5 tons jumbo bag 2 tons jumbo bag
High Quality Ilmenite Sand 40 - 45% We are offering ilmenite Sand (Tio2 : 40 - 45%) as per below mentioned specifications from India on regular basis Parameter Value TiO2 51 - 55% FeO 8 - 12% Fe2O3 20 - 24% Total Fe 20 - 26% SiO2 2 - 6 % Bulk Density 2300 - 2500 Kg/m3 Packaging Details In 50 Kg Bags or 1 Ton Jumbo Bags Port Vizag Supply Ability: 1000 Metric Ton/Metric Tons per Month, payment terms Payment; FOB, CNF, CIF, confirm L/C, or Cash against document with 30% advance payment.
PRODUCT INFO Bitter melons are small to medium gourds, averaging 6 to 30 centimeters in length, and have a long and slender, oblong shape with slightly tapered ends. The gourd's surface will vary depending on the specific type, ranging from deeply creased, smooth, pale green, and ridged to rough, dark green, and heavily textured with warts and bumps. The gourd's skin may also exhibit a waxy layer, and some rarer types of Bitter melon showcase a white hue. Underneath the thin skin, the flesh is crisp, watery, and pale green, encasing a central cavity filled with spongy pith and large, cream-colored seeds. Bitter melons are harvested when they are young and green, containing a sharp, astringent, and vegetal flavor. The gourds are also selected when they display a green coloring with a faint yellow hue, an indication of further maturity, rumored to contain a slightly milder, bitter, and acidic flavor. USES Bitter melons have an astringent, bitter flavor well suited for cooked preparations, including stir-frying, baking, saut�©ing, steaming, boiling, braising, and stewing. The melon's sharp flavor complements rich, fatty, and spicy ingredients and is often utilized in different culinary styles found within Asian cuisine. Bitter melons can be consumed raw, but the gourds should be deseeded, salted, and left for approximately 30 to 45 minutes to draw excess moisture and bitterness. Once the bitter flavor is lessened, the melons can be sliced for salads, chopped into dips and spreads, or blended into juices. Bitter melons are also traditionally blanched before use or salted to tame the astringent notes before cooking. The melons can be stirred into soups and curries, stuffed and baked as a main dish, stir-fried with vegetables and meat, or cooked and coated in rich sauces. Bitter melons can also be sliced and roasted as a simple side dish, cut and fried as a rice accompaniment, or pieces of the flesh can be dried and steeped as a healing and cleansing tea. In addition to the melons, the young leaves and shoots of the plants are edible and share the characteristic bitter flavor, used as an accent in salads and soups. Bitter melon pairs well with coconut milk, aromatics including lemongrass, ginger, garlic, and onions, chile peppers, tomatoes, green beans, eggplant, black beans, yogurt, pork, beef, and poultry, and seafood including fish, shrimp, crab, and scallops. Whole, unwashed Bitter melons will keep 3 to 5 days when wrapped in plastic or placed in a sealed container in the refrigerator's crisper drawer. SEASONS Bitter melons are available year-round, with a peak season in the summer.
PRODUCT INFO Peteh beans (Sator) pods are medium to large in size, averaging 30-45 centimeters in length, and are long, wide, ribbon-like, and sometimes twisted in shape. The green pods grow in clusters on tall trees, and when immature, the pods are flat and almost translucent. As they mature, the seeds begin to form within the pod causing protrusions, and the pod becomes tough, hard, and vibrant green. Inside the pod, there is a cream-colored, slippery film that encases the seeds and each pod can hold 15-20 seeds. The seeds are pale green and are similar in size to almonds. Peteh beans have an unusual smell, often compared to natural gas, and are crisp, soft, and tender with a rich and pungent flavor. Peteh beans (Sator) contain fiber, iron, calcium, potassium, vitamin C, riboflavin, and thiamin. USES Peteh beans (Sator) are best suited for cooked applications such as roasting, stir-frying, deep-frying, and sauteing. When young, the pods do not contain fully developed seeds and can be used whole in stir-fries or consumed raw, pickled, or fried. When mature, Peteh beans must be peeled before cooking and can be boiled in coconut milk or stir-fried with shrimp, curry paste, garlic, and chilies. It can also be roasted in the pods and eaten similar to edamame. To remove the seeds, carefully use a sharp knife to cut the pod or scrape the outer layer off into a bowl. Peteh beans can be dried, causing the seeds to turn black, and stored for extended use, or the beans can be pickled in a sour brine, creating a slightly rubbery texture without the loss of flavor. Peteh beans pairs well with chilies, garlic, onions, turmeric, lemongrass, kaffir lime leaves, shrimp paste, oyster sauce, shrimp, beef, pork, or poultry, and rice. The beans will keep for a week when stored in a cool and dry place and will keep for a couple of months when fermented. SEASON Peteh Bean is available year-round.
We are supplier and exporter of Marble. ble at competitive prices for both commercial as well as residential projects. These enhance the look of homes, restaurants, hotels and shopping complexes. Product Name : Marbles and Tiles , Grade : Grade A , Grade B , Grade C , Commercial Grade , Color and Type : Royal Cream , Smokey ,Crystal Cream Color and Sahara Beige Omani marble , Kamal basha & Mugla white turkey marble , Size (CM) : 30 * 30 , 30*60 , 60*60 , 33*15 , 33*12 , 30*15