V4 Borewell Submersible Pumpset Falcon Premium 100 mm (4) Borewell Submersible pump is firmly coupled to a submersible electric motor and Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosive resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification Power Range : 0.37 kW to 4.4 kW (0.50 HP to 6.0 HP) - Version : Single Phase 160V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. Single Phase available in 0.5 HP to 5.0 HP Three Phase available in 1.0 HP to 6.0 HP - Speed : 2880 RPM - Head Range : 10 Mtr. To 340 Mtr. - Discharge Range : 450 LPM to 12 LPM - Outlet Size in Inch : 1.0 , 1.25, 1.5 & 2.0 - Degree of Protection : IP 58 - Direction of Rotation Minimum Cooling : Counter clockwise from driving end -1ph: Electrically Reversible -3ph - Thrust Load : 0.37 kW â?? 0.75 kW- 650 lbs, 1.1 kW -1.5 kW -1000 lbs, 2.2kW, 7.5 kW -1500 lbs. - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR): 3ph Direct Online (D.O.L) - Maximum Starts Per Hour : 20 Times
V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m�²/sec (max.) - Ph Value : 6.5 to 8.5
V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
Tobee SP/SPR vertical slurry pump is designed for applications requiring greater reliability and durability than conventional vertical process pumps can offer. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Customized submerged length and suction agitator available. The SP/SPR vertical sump pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits.
Tobee SP/SPR vertical slurry pump is designed for applications requiring greater reliability and durability than conventional vertical process pumps can offer. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Customized submerged length and suction agitator available. The SP/SPR vertical sump pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits. Design Features: Less wear, less corrosion Wetted components are available in a wide range of alloys and elastomers, from which Weir Minerals selects the optimum combination of materials for maximum resistance to wear in virtually any industrial application, including those demanding both abrasion and corrosion resistance and where larger particles or high density slurries are encountered.
Tobee SP/SPR vertical slurry pump is designed for applications requiring greater reliability and durability than conventional vertical process pumps can offer. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Customized submerged length and suction agitator available. The SP/SPR vertical sump pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits. Design Features: Less wear, less corrosion Wetted components are available in a wide range of alloys and elastomers, from which Weir Minerals selects the optimum combination of materials for maximum resistance to wear in virtually any industrial application, including those demanding both abrasion and corrosion resistance and where larger particles or high density slurries are encountered.
Assay 99%
Plunger Type Pumps, Hydraulically Actuated Diaphragm Type Pumps, Mechanically Actuated Diaphragm Type Pumps, Solenoid, Operated Diaphragm Dosing Pumps, Complete Skid Mounted Dosing Systems, Chemical Process Pumps, Seal free Magnetic Drive Pumps, Progressive Pumps, Y Type Strainers, Pulsation dampners, etc.
PE coil pipes and tubes for water and wire cable conduit PL231 The PE coil pipes and tubes can be used: water pipe 4 â?? 6 â?? 1-inch black coil with pressure 1.6mpa, OD 20-75mm, WT 2.3-6.8mm pe conduit cable embedded wire cable and optical cable, OD 20-200mm, WT 1.8-3.5mm weak current protection tube and communication tube, OD 20-200mm, WT 1.8-3.5mm We use new 100% pure raw PE material WHY NEW MATERIAL HDPE PIPES? 1. Health performance PE pipe processing without adding heavy metal salt stabilizer, no scaling layer, and no bacteria. 2. Corrosion resistance It can resist various chemical media erosion, with no electrochemical corrosion. 3. Service life Under rated temperature and pressure conditions, PE pipes can be used for more than 50 years. 4. Impact resistance PE pipe toughness, high impact strength, heavy objects directly pressed through the pipeline will not break. 5. Connection performance The strength of the hot melt or electric melt interface of the polyethylene HDPE pipe is higher than that of the pipe body, and the joint will not be broken due to soil movement or live load. 6. Construction performance It has a lightweight pipe weight, a simple welding process, convenient construction, and a low overall project cost.
Basic Details Color: Transparent, green , blue, yellow , red ,white etc. Size:1.22*2.44m 1.5*3m 1*2m etc. Thickness: 1-200mm or as your request Packing: based on your requirement MOQ:1-2 ton Payment:T/T Key Features of Acrylic /PMMA 1.Good light transmission. 2.Good weather resistance. 3.Can be molded and reprocessed. 4.Widely usage, easy to dyeing and painting. 5.Non-toxicity. 6.High mechanical strength. 7.Light weight. 8.Good impact strength. 9.Good Insulation feature, widely used for different electrical equipment. 10.Good hard coating and scratch resistance 11.Good chemical resistance, superior to most other plastic materials. 12.Easy to clean and maintain.
Product Name: High Preessure Industrial Use Transformer Vacuumizer Packaging Wxf Series Anti-Explosive Oil Free Rotary Vane Vacuum Pump Summary: We have more than 20 types chemical process pump, such as horizontal pump, submersible pump ,vertical pump, semi-submersible pump, fluoroplastic pump, axial pump ,gear pump.ect . Application: They are used for transmission of liquids (oil, sea water ,sulphuric acid, phosphoric acid, H2SiF6acid, alkali liquid) with low or high temperature, neutral or corrosive liquids ,or liquids with solid granular and widely used in petroleum chemical industry ,oil refining industry, paper ,pulp industry ,sugar industry ,mining ,etc Lots of material can be chose for different working condition, such as cast steel ,stainless steel 304,316,2205,904L, Hartz alloy C276,C22, nickel-base alloy GH600, PVDF,PP, UHMWPE-lining .etc Pump a strong seal system :packing seal ,double face mechnical seal ,cartridge mechnical seal ,API682 flushing syestem.
Tobee 300TV-SP Vertical Slurry Pump is designed to be immersed in liquid for conveying abrasive, coarse particles, dirty water and particle contaminated water. Due to the design of the pump assembly, a shaft seal is not required and the pump can be operated in conditions that most pumps would have a low service life and their seal arrangement would not be effective.
Tobee 250TV-SP Vertical Slurry Pump is designed for applications requiring greater reliability and durability than conventional vertical process pumps can offer. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Customized submerged length and suction agitator available. The SP/SPR vertical sump pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits.
Tobee 100RV-SP Vertical slurry pump is designed for applications requiring greater reliability and durability than conventional vertical process pumps can offer. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Customized submerged length and suction agitator available. The SP/SPR vertical sump pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits.
Tobee 40PV-SP Vertical slurry pump is designed for applications requiring greater reliability and durability than conventional vertical process pumps can offer. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Customized submerged length and suction agitator available. The SP/SPR vertical sump pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits.
65QV-SP Vertical Slurry Pump is designed to handle diverse uses including all rugged mining and industrial applications, always ensuring reliable performance and excellent wear endurance. 65QV-SP vertical sump pumps are available in various standard lengths to suit common sump depths, offers a wide range of configurations allowing the pump to be tailored to a specific application. Wetted components are available in a wide range of alloys and elastomers. They are ideally suited for handling abrasive and corrosive liquids and slurries while submerged in sumps or pits.
Tobee 2QV-AF Froth Slurry Pump is vertical, double casing, single stage centrifugal forth pump, manufactured with advanced technology. The 2QV-AF froth pump can effectively eliminate the bubble in the slurry at work, even the slurry capacity is not enough the pump can work normally. It is suitable for various of flotation process and a perfect pump for handing frothy pulp indeed. AF vertical forth pumps capacity is much higher than that of other types slurry pump without shaft seal and sealing water. Design Features: Excellent performance, easy assembly & disassembly, high reliability and etc. Without shaft seal and sealing water. The discharge branch can be positioned at intervals of 45 degrees by request and oriented to Any eight positions to suit installations and applications.
Tobee 3QV-AF Vertical Froth Pump is designed to increase the pump ability of frothy slurries. The principle of operation is similar to that of hydrocyclone separation. Air is separated from the slurry in a vortex created by the impeller rotation and the tangential inlet to the pump's conical sump. This results in more efficient pumping at higher capacities and a smooth operation. It is ideal product for the transporting of slurries with lots of froth, especially the slurries in the minerals flotation processing. Design Features: Submerged in liquid, delivering abrasive & corrosive slurry which contains froth. Double casing structure No shaft seal and flushing water The parts immersed in liquid can be wear resistant metal or rubber Easy to maintain
Tobee 8SV-AF Vertical Froth Pump is latest generation of froth pump based on advanced technology at home and abroad. It is vertical shaft configuration, and comprise a hopper, with vertical bearing assembly. 8 inch froth slurry pump is designed for transporting high abrasive and corrosive froth slurries, Especially used in the flotation process. Design Features: Vertical froth pump is suitable for transporting slurry with froth, especially for flotation processing . It can eliminate the froth or foam in the running slurry and work normally even if the feeding slurry is not enough. The froth pump wet parts are made of Ni-hard and high chromium wear-resistant alloy materials. Funnel charging box is of steel structure. The discharge direction of froth pump can be oriented at intervals of 45°. The vertical froth pump adopts double-casing structure, with stable performance, high efficiency, wear resistance, and great interchangeability of components.
Tobee AF Vertical Froth Slurry Pumps are latest generation of froth pump based on advanced technology at home and abroad. It is vertical shaft configuration, and comprise a hopper, with vertical bearing assembly. AF froth slurry pump is designed for transporting high abrasive and corrosive froth slurries, Especially used in the flotation process. Design Features: Excellent performance, easy assembly & disassembly, high reliability etc. Dont need shaft sealing and sealing water. The discharge branch can be positioned at intervals of 45 degrees by request and oriented to any eight positions to suit installations and applications.
