SVR3L is made from latex harvested from our rubber plantation. It can meet customer strict requirement about some of technicalities such as: the PO, Color (Lovibond), SVR3L is made from latex harvested from our rubber plantation. It can meet customer strict requirement about some of technicalities such as: the PO, Color (Lovibond), Latex is preserved by ammonia or sodium sulfite. Then coagulated with formic acid, followed by shredding by passing through a rolling mill, washing system and hash.
Rubberwood is a light-colored medium-density tropical hardwood obtained from the Par rubber tree (Hevea brasiliensis), usually from trees grown in rubber plantations. Rubberwood is commonly advertised as an "environmentally friendly" wood, as it makes use of plantation trees that have already served a useful function
Butyl Reclaimed Rubber
Shampoo, soap, toothpaste, shaving razor, hand body lotion, household cleaning products, coffee beans, instant coffee, coffee mix, tea, chocco, biscuits, wafer, cookies, milk, candy, canned food.Buying & sourcing agent
Natural Reclaimed Rubber
SVR 10 is a mixture of cup lump (the dried latex left in the bottom of tapping cups), tree lace (the strings of dried Rubber left along the tapping groove of the trees after tapping), and sometimes field coagulum (any late coagulated by a smallholder either in a collection vessel or on the ground). Loose bale : 33.33kg/bale or 35kg /bale 20-21.5 MT/ 20'FCL Wooden pallet : 36 bales/pallet , 16 pallet/20'FCL : 19.2MT/FCL with 33.33kg 20.16MT/FCL with 35k
SVR 10 is a mixture of cup lump (the dried latex left in the bottom of tapping cups), tree lace (the strings of dried Rubber left along the tapping groove of the trees after tapping), and sometimes field coagulum (any late coagulated by a smallholder either in a collection vessel or on the ground). Loose bale : 33.33kg/bale or 35kg /bale 20-21.5 MT/ 20'FCL Wooden pallet : 36 bales/pallet , 16 pallet/20'FCL : 19.2MT/FCL with 33.33kg 20.16MT/FCL with 35k
SVR3L is made from latex harvested from our rubber plantation. It can meet customer's strict requirement about some of technicalities such as: the Po, Color (Lovibond), This product is being applied in many fields: advanced automobile tire, wire belt, wire cable, sole of shoes, medical products, industrial electronics,
Super Fine and High Tensile Grade as per customers requirements
SVR3L is made from latex harvested from our rubber plantation. It can meet customer's strict requirement about some of technicalities such as: the PO, Color (Lovibond), SVR3L is made from latex harvested from our rubber plantation. It can meet customerâ??s strict requirement about some of technicalities such as: the PO, Color (Lovibond), â?¦ Latex is preserved by ammonia or sodium sulfite. Then coagulated with formic acid, followed by shredding by passing through a rolling mill, washing system and hash. After the crumb rubber is dried, it will be compressed into blocks and packed in polyethylene bags
Food product, fmcg products, toothpaste, toothbrush, mouthwash, soap bar, liquid hand wash, body wash, face wash, shampoo & conditioner, body lotion, body cream, body moisturiser, sun control, shaving razor, shaving cartridges, shaving blade, shaving gel, shaving foam, shaving cream, after shave, hair colour, talcum powder, fairness cream, deodorant, roll on, deodorant spray, sanitary napkins, baby diapers, baby wipes, detergent powder, liquid detergent, detergent bar, cleaning powder, cleaning liquid, liquid hand sanitizer, antiseptic liquid, disinfected spray, beverages, tea bag, loose tea, flavoured herbal tea, baby food, candy, chocolate, confectionery, office stationery, and snuff , condoms, beverage and cold drink.
Hollow Plastic Concrete Formwork for fundational building Size:1220*2440mm Thickness:15mm/18mm/20mm MOQ:100pcs Advantage:Reusable Application:concrete panels building formwork Color:Grey Weight:31kgs Quick Details: Product Name: Plastic concrete formwork Application: Concrete panels building formwork Material: PP plastic material Surface: Cleanly ,Glossy and smoothy Size: 1220*2440mm Thickness: 15mm, 18mm,20mm Type: Construction formwork Color: Grey Certificate: ISO9001:2008 Weight: 31KGS Packaging & Delivery Selling Units:Single item Single package size: 244X122X2.0 cm Single gross weight:31.0 kg Package Type:carton box packing onto wooden pallet Lead Time : Quantity(Piece) 1 - 200 201 - 336 337 - 810 >810 Est. Time(days) 5 7 15 To be negotiated
Bar mops, dish cloth, duster cloth, floor cleaning cloth, stockinet rolls, face cloth, hand towels, bath towels, beach towels, kitchen towels, tea towels ( stripped, checked, printed, embroidered, jacquard ), waffle weave kitchen towels, glass cloth, herringbone kitchen towels, terry tea towels, mono check tea towels, aprons, pot holders, hot pad, oven mitts, silicon oven mitt, terry oven mitt, pan grabbers, chef hat, caps, socks ( cotton, polyester ), cotton rag rugs & mat, bed sheets, table cloth, napkins, cushion covers, thermal blankets, fleece blankets, mink blankets, floor carpet, cotton bags, tote bags, shopping bags, jute bags, paper / board bags, fruit picking bags, coin bags, cotton webbing tape, cotton/ polyester braided cards, home textiles & made ups, jute webbing, pp webbing, soft plant tie, coconut coir pith / peat..
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
1.We use imported base paper from Germany. For solid color, base paper most 80 to 120GSM. For wood base paper is between 70-85 gsm 2. High quality water-base ink- Available over 200 shades in Solid colors and wood grains 3. With clear texture ,high Fidelity meeting international standards. 4. With smooth surface coating 5. Germproof, mould proof, antistatic and wear-resistance. 6. Green environmental protection and Odorlessness which Conforms to the GB18584-2001 standard requirement 7. Can be used for the hot press molding craft, the production efficiency is high. 8. Melamine paper takes shape easily, is widely used for the panel furniture and the decorative yarn. Product Specification: Width: 1230-1260mm or 1300-1800mm Length: 500-1000m For storing: Put it in room to a cool and dry place keep the temperature 20-25°C in room. The best humidity is: 50-60% We can also give you complete decorative solution with Matching Melamine Edge Banding, PU Paper. If you need just need Melamine/prelaminated boards either in MDF / Particle board we can also do so
We supply balustrade and its related components like connectors, saddles, pipes end caps in SS201, SS304, SS316, SS316L. Pipes OD42.2mm*2mm. Also available other OD on request. Balustrade shape round, square any other custom designed shape. Height about 1060mm. Finish: satin, Glossy.