HR3210 Micro-power Pressure Transmitter overviews HR3210 series are lower power consumption pressure transmitter,which produced especially to measure liquid pressure in the field without power supply. It is stable, reliable, high precision and easy to assembly and disassemble. It uses well-known brands pressure sensor in the world and 1Cr18Ni9Ti stainless steel structure, intrinsic safety type circuit design. The biggest advantage of the transmitter is low power consumption , the operating current is lower than 900uA, so it is easy for dry battery to supply in the field. Quick response, the single-chip can be used to make the intermittent power supply pressure acquisition system. It can reach the balance within 400 uS when power on, obtain accurate data, and then turn off the power. It will turn on when collecting data. Features .Long time and reliable operating .Low power consumption, high accuracy .Protection by the isolated and stainless steel 316L diaphragm, anti-corrosion Specifications Range 0ï½?1ï¼?1.6,2,2.5ï¼?â?¦100Kpaï¼?MPa Over-load liquid level 1.5tims F.S accuracy ±0.25%FS, ±0.5%FS, ±1%FS (Non linearity, repeatability, hysteresis) Operating Temp. ï¼?15ï½?+60 Compatible medium Compatible with 1Cr18Ni9Ti and fluoro rubber Operating current < 900uA Output Signal 0.25ï½?2.25Vdcï¼?0.25-2.25Vdcï¼?0.5-4.5Vdc Voltage 3ï½?5Vdcï¼? Insulation > 100MΩ@500V Electrical connections Direct cable, housing protection IP65 Pressure interface M20Ã?1.5M; or customized Response time
HR3288 HART Smart Pressure Transmitter Overview .HR3288 HART protocol Smart Pressure Transmitter is a high-precision, high-stability, multi-parameter, 4.5 Digit LCD displayed intelligent pressure measurement products which complies with the HART® protocol. Users can use the HART communicators to manage, adjust or monitor process variables when HART instruments running in the process, or use the buttons for on-site configuration ,it's easy to operate. .This product adopts the latest application results of digital technology in the field of sensor manufacturing, and combined with the most advanced designing and manufacturing pressure transmitter technology in the world, precision digital temperature compensation and nonlinear calibration technology, safe and reliable explosion-proof structure and standardized signal output with high accuracy and wide range coverage,its also adapt to the place where fluid pressure is precisely measured. .The product works in a two-wire mode and can be directly replace the simulative two-wire 4mA-20mA DC output transmitter. Digital communication with manual operator. Electromagnetic radiation fits IEC801 standard. Features .4mA~20mA DC current output superposition HART protocol digital communication (two-wire system) . Digital compensation and nonlinear calibration techniques . Digital error correction with local, remote zero and range calibration functions . digital wide temperature compensation in -10 ° C ~ 80 ° .can be operated by buttons to facilitate configuration. .Reverse power protection, over voltage protection . Anti-surge, Anti-electromagnetic interference
Model: CJBPZ-I Description: CJBPZ Intelligent Pressure Transmitter is a highly integrated measurement product with high stability.It uses intelligent processing circuit, the most advanced design and manufacturer technology of piezoresistive pressure transmitter, and is available for pressure signal and temperature signal output that in accordance with standard MODBUS-RTU protocol. Featuring integrated design, standard digital output, great compatibility, small size, high accuracy, light weight and wide pressure range, it can be applied in many fields which involve high accuracy required measurement of fluids. Features: RS485 communication interface, Standard MODBUS-RTU Protocol output Netting available Short protection and reverse polarity protection Full stainless steel construction, compact size, light weight Good output consistency and replaceability Available for calibration and parameter change on site through matched soft of upper computer Application: Measure temperature of gas or liquid which is compatible to 316L stainless steel Used in field of petroleum, chemical industry, Metallurgy, Electricity, hydrology etc Performance Parameters: Range: -100kPaâ?¦0kPa~10kPaâ?¦100Mpa (Pressure); 0m~3.5mâ?¦200mH2O (Level) Pressure type: Gauge / Absolute Over pressure: 1.5 times FS / 110MPa (min. value is valid) Accuracy: ±0.5%FS Stability: ±0.3%FS/YEAR Zero thermal drift: ±0.04%FS/â??(â?¤100kPa); ±0.03%FS/â??(ï¼?100kPa) Span thermal drift: ±0.04%FS/â??(â?¤100kPa); ±0.03%FS/â??(ï¼?100kPa) Output: RS485 Interfaceï¼?MODBUS-RTU protocolï¼? Application Temp.: -10â??~60â?? Measurement Error: ±2â?? Storage Temp.: - 40â??~85â?? Power Supply: 9Vï½?28V DC, 15V DC (recommended) Insulation: 100V, 100M Shock: 20g, 25Hz~2000Hz Impact: 100g, 11ms Protection: IP65(B1,B2); IP63(B3); IP68(Level) Electric Connection: Cable or Junction Box Weight: about 160g Housing: S.S. 316L Diaphragm: S.S. 316L O- Ring: Viton Remark: Shrinking range : 1/5 basic range, no range extension. For special temperature requirement, please feel free to contact our company.
Key Features: 1.High accuracy 2.Robust and compact design 3.Overload protection 4.High vibration resistant 5.Minimum hysteresis Key Specifications: 1.Measuring range: -1.0 ~ 0.0 bar to -1.0 ~ -24.0 bar (max. pressure: 3 ~ 80 bar) 0.0 ~ 1.6 bar to 0 ~ 60.0 bar (max. pressure: 5 ~ 200 bar) 2.Linearity: < 1% full scale 3.Hysteresis: < 0.5% full scale 4.Permissible ambient temperature: 0° C ~ +60° C 5.Permissible medium temperature: 0° C ~ +85° C 6.Protection class: IP65 acc. to DIN EN 60529 7.Materials (media contact): chrome nickel steel 1.4305, ceramics, AL2O3, gaskets 8.Material (housing): Chrome nickel steel 1.4305 9.Nominal power supply: 24 VDC / AC 10.Output: linear, 4~2-mA / 0~10 V, 2/3-wire Industrial areas: 1.Nuclear power plants 2.Thermal / gas fired power plants 3.Chemical & manufacturing industries 4.Semiconductor plants
Key features: 1.Direct measurement, without transfer fluid 2.High vibration resistance 3.High accuracy 4.High overpressure safety 5.Minimum hysteresis Key specifications: 1.Measuring range: 0 ~ 1.6 bar to 0 ~ 60 bar (overpressure safety: 3.2 bar ~ 120 bar) -1.0 ~ 0.0 bar to -1.0 ~ 15 bar (overpressure safety: 2 bar ~ 32 bar) 2.Linearity: < 1% full scale 3.Hysteresis: < 0.5% full scale 4.Permissible ambient temperature: 0, ° c ~ 60, ° c 5.Permissible media temperature: 0, ° c ~ 100, ° c 6.Nominal power supply: 24v dc 7.Output signal: 0~20ma / 4~20ma / 0~10v, 3-wire 8.Ingress protection: ip65 acc. To din en 60529 9.Temperature drift, zero: 0.4% full scale / 10k 10.Temperature drift, range: 0.05% full scale / 10k 11.Electrical connection: connection plug m16 x 1.5 acc. To din en 175301-803 12.Material, medium contact: aisi 316l (1.4404), gasket: viton 13.Material, body: aisi 304 (1.4305) Industrial areas: 1.Chemical industries 2.Machine and plant engineering 3.Process engineering 4.Manufacturing industries 5.Glass and silicon industries
Features: Suitable for industrial application. Wide measuring range. Sensor type: Piezoelectric differential pressure module Measuring range: 50 ... 10000 pa Output: 4 ... 20 mA / 0 ... 10 V Accuracy: 2.0% F.S. IP rating: IP65
PTX201 is suitable for measurement of liquid or gas pressure, even for difficult media such as contaminated water, steam and mild corrosive fluids. >All stainless steel construction >Excellent load cycle stability and shock resistance >4~20 mA, 2-wire output >Ranges up to 400 barg >DIN 43650 plug-in connector >Higher ranges on request >Integral LED or LCD display
PTX201 is suitable for measurement of liquid or gas pressure, even for difficult media such as contaminated water, steam and mild corrosive fluids. All stainless steel construction Excellent load cycle stability and shock resistance 4~20 mA, 2-wire output Ranges up to 400 barg DIN 43650 plug-in connector Higher ranges on request
PTX201 is suitable for measurement of liquid or gas pressure, even for difficult media such as contaminated water, steam and mild corrosive fluids. All stainless steel construction Excellent load cycle stability and shock resistance 4~20 mA, 2-wire output Ranges up to 400 barg DIN 43650 plug-in connector Higher ranges on request
PTX201 is suitable for measurement of liquid or gas pressure, even for difficult media such as contaminated water, steam and mild corrosive fluids. All stainless steel construction Excellent load cycle stability and shock resistance 4~20 mA, 2-wire output Ranges up to 400 barg DIN 43650 plug-in connector Higher ranges on request
NCS-PT105 series Smart Pressure Transmitter with advanced, mature, reliable 3151 capacitance sensors has been designed meticulously by combining advanced microprocessor technology and digital capacitance measurement technology. The powerful functions and high-speed computing capability of the microprocessor make it have excellent qualifications such as smart, high precision, high reliability, stable zero and so on. Its LCD can display many physical parameters (e.g. pressure, temperature, current and so on). It can realize the functions such as zero adjustment, range settings by key-press operation, and it is easy for field testing. NCS-PT105 series Smart Pressure Transmitter supports HART, FF, and PA protocol and can measure pressure, differential pressure, liquid level, flow, and other industrial parameters. It can be widely used in the petroleum, chemicals, electricity, and metallurgical industries, etc.. According to the type of measurable pressure: Model Pressure type NCS-PT105 SR Micro-differential pressure transmitter NCS-PT105 SG Gauge pressure transmitter NCS-PT105 SA Absolute pressure transmitter NCS-PT105 SD Differential pressure transmitter NCS-PT105 SH Differential pressure transmitter for high static pressure According to the protocol: Model Communication Protocol type NCS-PT105 H HART NCS-PT105 F FF H1 NCS-PT105 P PROFIBUS PA As a transitional communication protocol in fieldbus, HART protocol achieves digital transmission on the existing analog transmission lines, and is compatible with existing analog signal control system. Either FF H1or PROFIBUS PA is a new generation of digital communication protocol, used in field connection, and linking field devices. International Standard IEC61158-2 is used in physical layer. Therefore, either FF H1or PROFIBUS PA is fieldbus actually. As following, Smart Transmitter with HART protocol is named as HART Smart Transmitter; Smart Transmitter with FF H1 protocol is named as FF Smart Transmitter; Smart Transmitter with PROFIBUS PA protocol is named as PA Smart Transmitter, All of these (Transmitters with the three types of fieldbus protocol) are named as Smart Pressure Transmitters or Smart Transmitters. In addition, HART Smart Transmitter has passed explosion-proof certification from National Supervision and Inspection Center for Explosion Protection and Safety of Instrumentation (NEPSI).
Intek Instruments is engaged in offering a wide gamut of high quality Pressure Transmitter / Transducer. 1. Brand:- Gefran Italy 2. Series:- KS Series 3. Pressure Range:- from 1 Bar to 1000 Bar 4. Output Voltage:- 0-10 VDC or 4-20 mA 5. Wetted Parts:- Stainless Steel 6. Accuracy:- < ± 0.5% FS 7. Response Time:- < 1 msec. 8. Application:- Suitable for all industrial applications, especially, on hydraulic (presses, pumps, power pack, fluid power, etc.) with severe conditions usually with high level of shock, vibration, and pressure and temperature peaks.
Since 1969, the innovative rosemount 1151 pressure transmitter has provided the process control industry with unsurpassed service. With over four million transmitters in service worldwide, the 1151 continues to offer industry leading value and quality. The rosemount 1151 is world-renowned for proven field performance, reliability, and longevity. 1151 transmitter: The 1151 transmitters bring true precision and measurement to differential, flow, gage, absolute, vacuum, liquid level, and specific gravity applications. Compact design, integral junction box, and local span and zero adjustments simplify installation, calibration, and commissioning. -
Features: 3 1/2 led/lcd display Compact outline, easy installation Strong compatibility Adjustable pressure unit Applications: The oil industry, chemical industry, electric power. Hydraulic pressure system, pneumatic system Energy and water treatment system. Automation equipment Industrial process control Performance parameters Reference temperature: Measuring range -0.1~250mpa Pressure type:Gage pressure, absolute pressure Output signal :4~20ma , 0~10v or others Display type3 1/2 led or lcd display Accuracy(%fs)0.10.250.5 Damping ( second )Adjustable Operating voltage(v)12~36v dc(standard 24v) Operating temperature: -20~85c Overload capacity(%)300 Life spanMore than 9 million times pressure cycle MediaMedia compatible with 316l Diaphragm material316l or ceramic diaphragm Housing material1cr18ni9ti Pressure interfaceM20*1.5, g1/2, g1/4, 1/4npt or others Enclosure ratingIp65 Weight 280g Carton size:l13cm*w6cm*h5.5cm Weight:0.5kg
FUJI FKC Differential pressure transmitter ( FUJI FKC Flow Transmitter FUJI FDC Differential pressure transmitter ( FUJI FDC Flow Transmitter FUJI FKC Flow transmitter ( FUJI FKC FUJI FDC Flow transmitter ( FUJI FDC 1.Product Introduce The Fuji FCX -AIII differential pressure (flow) transmitter accurately measures differential pressure and converts it into an output signal of 4~20mA DC. Fuji transmitter utilizes a unique micromachined capacitance silicon sensor with advanced floating capsule structure and newer micro-processing technology, the transmitter has high accuracy, good stability, safety and reliability, and easy to use. It's small volume, light weight, good environment adaptability, and applicable to all fields. If using the hand held communicator(sold separately), it can be set and display via remote operation, without affecting the DC 4~20mA output signal of transmitter. Fuji FCX-AIII series transmitters with safety funtion have obtained the certificate of SIL certification by T�?V. 2ï¼?Fuji FKC Transmitter Features a. High accuracy Differential pressure (flow) transmitter can be carried out with high accuracy measurement in the range of 0.1 20000kPa. Standard accuracy: ± 0.065% High accuracy(optional) ± 0.05% There's no need to linear calibration when carrying out zero elevation or suppression. b. Excellent environmental adaptaboility The advanced floating cell protects sensor from temperature,static pressure and overpressure effect, and controls the total measurement error of the filed to the minimun. c. Excellent operability and easy to use Built-in RFI filter and lightning arrester Various anti-corrosive materials Built-in local configurator with 3 push buttons d.The transmitter can communicate using FUJI, HART, communication protocol, and also can use FOUNDATION FIELDBUS or PROFIBUS protocol after changing the electronic circuit. 3:Product Specification Measured fluid: Liquid,Gas,or vapour Range, operating pressure, and overrange limit:
Quick Details Place of Origin: Sichuan, China (Mainland) Brand Name: SAND Model Number: PT124B Pressure Range: 0~5~150MPa / 0~500~20000psi Accuracy: ±1.0%FS Power: 24VDC(9~36VDC) Output: 0~5V or 1~5V or 0~10V or 0~20mA or 4~20mA Probe Temperature: 400 Temperature Drift:
HR310 Series Digital Pressure Transmitter 1.overview HR310 series digital pressure transmitter is one of excellent products in our company, Which use advanced and mixed signal processing technology and unique compensation methods to realize high precision digital pressure measurement, Full scale digital linear calibration, full temperature digital compensation, compensation parameter stored in nonvolatile memory, multiple safety protection system to avoid the products cannot be used due to calibrate parameter lost; part of Circuits have power and watchdog monitor, mechanical part with full seal stainless steel structure, both of them remarkably improve the reliability of transmitter. The high precision digital pressure transmitter is widely and successfully used in many industries, such as pressure measurement in industrial process, hydrology and water conservancy, and geological prospecting etc. 2. Features High stable pressure sensing unit, with long-term stability High precision, up to 0.05ï¼?F.S(Linearity, repeatability, hysteresis); Adopts mixed signal microprocessor and Higher order fitting algorithm to realize high precision compensation Standard RS485 MODBUS-RTU Protocol, can be used in DCS or PLC system Low power consumption, when operating at full scale then the power consumptions about 4mA, outstanding advantage when use outside battery supply Anti-surge, electromagnetic interference
Key Features: 1.Configurable measuring range 2.Configurable parameters via LCD Display, keypad 3.Integrated operating pressure measurement up to 40 bar 4.Suitable for non-corrosive gaseous media and vapour 5.Corrosion resistant field housing 6.Oil and grease free for oxygen applications Key Specifications: 1.Measuring range: 0 ~ 160 mbar to 0 ~ 2.5 bar 2.Maximum static pressure: 40 bar 3.Design: Differential pressure measurement, with or without integrated operating pressure measurement (25 bar or 40 bar) 4.Electrical output: differential pressure & operating pressure â?? 4-20mA 2-wire connection 5.Maximum pressure load: one-sided overpressure-proof up to the rated pressure of the measuring system, resistance to under-pressure on the (+) and (-) side 6.Linearity: < 1% Full scale 7.Ambient temperature: -20 �°C to +70 �°C 8.Admissible media temperature: -20 �°C to +70 �°C 9.Characteristic curve: linear 10.Pressure connection: inner thread G 1/4 cutting ring screw connection for 8 or 10 mm pipe 11.Measuring membrane: 1.4305 NiBe for differential; Al2O3 for operating pressure 12.Protection: IP65 as per EN 60529, with integrated ceramic sensor Application areas: 1.Filter condition monitoring 2.Flow measurement and control 3.Pump Control Application areas: 1.Nuclear power plants 2.Manufacturing and chemical plants 3.Marine, shipping application 4.Onshore and offshore area 5.Petrochemical, solvent industry 6.Sewage, effluent treatment plants
HR3051-LT Differential Pressure Level Transmitter overview The diaphragm of the differential pressure level transmitter is used to prevent the medium in the pipeline from directly entering the pressure sensor component of the differential pressure transmitter. It uses a filling fluid such as silicone oil to transmit pressure between the transmitters. The HR3051-LT differential pressure level transmitter be used for measuring the level, density, pressure, and flow of a liquid, gas, or vapor and converts it into a 4-20 ma DC HART current signal output. The RP2001 can also communicate with the RST375 handheld te rminal or the RSM100 Modem for parameter setting, process monitoring, and more. The measuring range of the HR3051-LT differential pressure level transmitter (when not moved) is 0-1kPa~2MPa, and the rated pressure of the liquid level flange is: 1.6/4MPa, 6.4MPa, 10MPa, 150psi, 300psi or 600psi. Working principle and structure The HR3051-LT differential pressure level transmitter consists of a HR3051-DP differential pressure transmitter and a soldered liquid level flange. Its working principle is the same as HR3051-DP type differential pressure transmitter (see HR3051-DP type differential pressure transmitter technical specification), except that the pressure transmission path on the positive pressure side is slightly different: the pressure acting on the high pressure side is firstly The diaphragm and filling liquid on the liquid level flange pass through the transmitter body and finally reach the high voltage side of the measuring sensor. Comparison of range code and range limits Range code Minimum range Maximum range Rated pressure (maximum) B 1kPa 6kPa Rated pressure of the liquid level flange
Pressure transmitter Differential pressure transmitter Make: sensor-tech, Italy All wetted part: s.S-316 Accuracy : 0.25 %/ 0.5%/ 0.1% Range : 0- 250 mbar------2000 bar Output signal: 4 . .20 ma, 0 .. 5 vdc, 0 .. 10 Vdc, other on request Power supplier: 10 ... 28vdc (current output) 15 .. 30 vdc (voltage output) Process connection: g1/4 or g1/2
