We supply Co-rotating parallel twin screws extruder for PE/PP filling with high percentage of up to 82% CaCO3/ 60%Talc/70%TiO2/45%Carbon powder/and 30% inorganic and organic pigments. Salient Features of co-rotating twin screw extruder EC52: 1) Main motor 55kw, L/D=40 2) One venting port and one vacuum port 3) Screw rpm: 60-600rpm 4) The output capacity: 150~200kg/h 5) One mixer, one main feeder and one side feeder 6) One soft water cooling system, one vacuum system and one filter system 7) Strand cutting unit with water bath, air blower, pelletizier and classifier 8) One control panel. Painted with anti-corrosion oil, and covered with plastic film, fumigation cost is on Buyer's side, if any.
We supply twin screw extruder for PLA/PE filling with (cassava/corn/potato)starch, PBS degassing, PLA/PBS alloy and so on. Salient Features of co-rotating twin screw extruder SAT65: 1) Main motor 90kw, L/D=40 2) One venting port and one vacuum port 3) Screw rpm: 60-400rpm 4) The output capacity: 150~250kg/h 5) One mixer, one loader and one feeder 6) One soft water cooling system, one vacuum system and one filter system 7) Air cooling die face cutting system with cyclone and classifier 8) One control panel. Painted with anti-corrosion oil, and covered with plastic film, fumigation cost is on Buyer's side, if any.
Sjsz conical twin-screw extruder Screw barrel:38crrm nitriding Hard tooth surface gear wheel box Vacuum venting device Forecd feeding system Electric macine; simenz Temperature controller: omron Frequency adjustment: helipu Power: 37kw Heater: cast aluminum stainless steel Size:4235*1520*2450 weight:4000kg
Jintech twin screw extruder
Specification: Screw diameter: d15- d 300 L/d ratio: 15-46 Product classification: Aiming at different plastic products the screw can be chosen from: general type, pin type, barrier type, separation type, and gas-exhausting type, etc. Base materials: (1)38crmoala(jis sacm645) (2)42crmo(aisi 4140) (3)4cr5mosi v1 (jis skd-61) (4)9cr18mov (5)hpt Bimetallic alloy materials: 1)fe-based alloy 2)ni-based alloy/deloro alloy 3)co-based alloy 4)nico-based alloy 5)tungsten carbide/wolfram carbide Technics: Heat treatment High-frequency quenching Nitriding treatment Hard-chrome electroplating Bimetallic alloy welding Bimetallic alloy centrifugal casting Technical parameter: Nitrided layer depth: 0.5-0.8mm Nitrided hardness: 900-1000hv Nitrided brittleness: less than grade 1 Surface roughness: ra0.4 Linearity of screw: 0.015mm Hard-chrome plating hardness after nitriding: >950hv Chrome-plating layer depth: 0.025-0.085mm Bimetallic layer depth: 3mm Slushing oil coated& film wrapped in wooden case
China hot sale pvc twin screw extruder SHJ SERIES CO-ROTATING TWIN SCREW EXTRUDER TECHNICAL PARAMETER MODEL SHJ-20 SHJ-30 SHJ-36 SHJ-43 SHJ-50 SHJ-63S SHJ-72 SHJ-72M SHJ-92 SHJ-92M SHJ-133 SCREW DIAMETER 21.7 30.5 35.6 43 50.5 62.4 71.7 71.7 92.4 92.4 132.2 SCREW DEPTH 3.85 4.6 6 7.5 9 11 12.6 12.6 15.5 15.5 23.6 L/D 32~40 34~49 35~50 35~55 32~56 32~56 32~56 44~56 32~56 32~56 32~56 ROTATING SPEED 600 600 600 600 600 600 600 600 600 600 400 MOTOT POWER 3 (4) 11~18.5 15~30 15~30 45~90 45~90 110~250 160~250 250~540 315~540 600~800 CAPACITY 2~12 30~60 40~80 40~80 80~200 150~450 300~800 600~800 600~1500 800~1500 1500~2500 EQUIPMENT IS MAINLY COMPOSED: 1) double-screw extruder 2)double-plunger hydraulic network 3)hydraulic bypass valve 4)under water pelletizing system(underwater pelletizing machine, centrifugal machine, water pipe, electrical control system). The advantages of underwater pelletizing machine system: 1)Outstanding quality of particle 2)High efficiency 3)Strong reliability 4)Safe operation 5)The special formula plastic granulation 6)High output 7)Small noise Our services 1. Purchase Service LAIZHOU CHIYUAN has a special and efficient working team. If you are new in the printing and packing area, some samples of your products could be sent to us, and we can give you some professional suggestion. 2. Shipping Service LAIZHOU CHIYUAN has an independent department for shipping. Our Colleagues are familiar with T/T and L/C and all documents could be made efficiently and carefully. We can provide the economic shipping way for you. 3. Installation & Clients Training Services LAIZHOU CHIYUAN can appoint engineers to provide installation and technical support to your company. 4. After Sale Service LAIZHOU CHIYUAN machines have at least one year warranty, also we could provide some spare parts for free.
Over 29 years experience in screw and barrel , more info pls find kaylee(at)tizatech.com Specification: Diameter: Ã?15-Ã?500 L/D ratio:15-55 Base Materials: 1)38CrMoAlA(SACM 645) 2)42CrMo(AISI 4140) 3)Cr12MoV(SKD11) 4)4Cr5MoSiV1(SKD61) 5)9Cr18MoV 6)40Cr Bimetallic Alloy Materials: 1)Fe-based alloy 2)Ni-based alloy 3)Co-based alloy 4)Tungsten carbide Processing Technology: Heat treatment High-frequency quenching Nitriding treatment Hard-chrome electroplating Bimetallic alloy welding Technical Parameter: Nitrided layer depth:0.50-0.80mm Nitrided hardness: 900-1100HV Nitrided brittleness: Less than 2 level Surface roughness: Ra 0.4 Linearity of screw: 0.015mm Hard-chrome plating hardness: â?¥950HV Chrome-plating layer depth: 0.025~0.10mm Bimetallic layer depth: 2 mm Bimetallic hardness: HRC50-65 Material to be extruded: PP, PE, PVC, ABS, AS, PS etc. We can manufacture all types of screws and barrels according to clientsâ?? requirement
Specification: 45/90, 45/100, 50/105, 51/105, 55/110, 55/120, 58/124, 60/125, 65/120, 65/132, 68/143, 70/135, 70/140, 75/150, 80/143, 80/156, 92/188 The above are standard specifications, we can customize according to customers' requirements. The compression ratio of screws can be designed according to different products and ingredients. Base materials: 1)38crmoala(jis sacm645) 2)42crmo(aisi 4140) 3)4cr5mosi v1 (jis skd-61) 4)9cr18mov 5)hpt Technics: Heat treatment High-frequency quenching Nitriding treatment Hard-chrome electroplating Bimetallic alloy welding Bimetallic alloy centrifugal casting Technical parameter: Nitrided layer depth: 0.5-0.8mm Nitrided hardness: 900-1000hv Nitrided brittleness: less than grade 1 Surface roughness: ra0.4 Linearity of screw: 0.015mm Hard-chrome plating hardness after nitriding: ¡ý 950hv Chrome-plating layer depth: 0.025-0.085mm Bimetallic layer depth: 3mm Slushing oil coated& film wrapped in wooden case
Screw diameter: 35mm-200mm Length: less than 10000mm Barrel diameter: 35mm-200mm Material: 38crmoala; skd61; skd11; 40cr; 42crmo; high quality alloy steel Technology for tin coated screw barrel/: nitriding treatment, alloy coating spraying, heat-treatment, quenching Appliance for tin coated screw barrel/: pa, evoh, eaa, pc etc
Model TSK75 Inner bore Diameter 60 Hardness 38-42HRC Tensile Strength 1300MPa Yield Strength 1100MPa Standard DIN, GB, JIS, ANSI Technics CNC Machining Feature Wear Resistant Material Stainless Steel Categorie: closed, feed, degassing, side-feeding, combi
Twin screw extruder food extruder from jinan reno company of china, we are special on snacks extruder machinery manufacturer and supplying . Our twin screw snacks extruder is slg70-ii extruder, output 150-200kg/hour, with the oil cooling system automaticly, the barrel cooling system too, twin screw feeder system, the screw length is about 1510mm.Diameters 70mm .
Twin Screw Extruder Twin screw extruder is developed on the basis of single screw extruder. The emergence of twin-screw extruders has replaced the traditional single-screw extruders with low efficiency and cumbersome operation. Description Twin screw extruder is developed on the basis of single screw extruder. The emergence of twin-screw extruders has replaced the traditional single-screw extruders with low efficiency and cumbersome operation. Raw materials such as rice, corn, soybeans, and wheat in daily life are extruded through a twin-screw extruder, and then formed into triangles, circles, hexagons, and cartoon shapes by rolling or stamping. Various flavors can later be produced by frying, baking or seasoning. Application Twin screw extruder is well used for extrusion production of pet food, aquatic feed industries, and soya industries and for massive productions with low starch content and high percentage of protein and fat, to realize a wide variety of sizes and shapes of final products, etc. Features Stainless steel auger feeder by inverter controlled; Stainless steel differential dual pre-conditioner, with steam and water inlets; Integral gearbox, oil bath, external oil cooling; Inverter-controlled main motor; Inverter-controlled cutting motor; Crane sliding cutting set; Hinge design molding headset;
Twin-screw Extruder Twin screw extruder is developed on the basis of single screw extruder. The emergence of twin-screw extruders has replaced the traditional single-screw extruders with low efficiency and cumbersome operation. Description Twin screw extruder is developed on the basis of single screw extruder. The emergence of twin-screw extruders has replaced the traditional single-screw extruders with low efficiency and cumbersome operation. Raw materials such as rice, corn, soybeans, and wheat in daily life are extruded through a twin-screw extruder, and then formed into triangles, circles, hexagons, and cartoon shapes by rolling or stamping. Various flavors can later be produced by frying, baking or seasoning. Application Twin screw extruder is well used for extrusion production of pet food, aquatic feed industries, and soya industries and for massive productions with low starch content and high percentage of protein and fat, to realize a wide variety of sizes and shapes of final products, etc.
It has been the professional manufacturer and the model company for advanced and high efficient extrusion food machinery in this field. congregates an expert team with twenty-year experiences in this extrusion machine industry, not only working hard to constantly researching extrusion technology, but also exploring food processes in order to benefit our clients producing creative food. Categories as follows: Puffing food machinery Fried snack machinery Fortified rice production line Vegetarian food production line Pet food machinery
Extruder:EPDM sheet extrusion machine,EVA interior sheet extruder,Rubber sheet extrusion machine,such as rubber and plastic sheet extrusion machine. Features: 1.The characteristics of the machine is advanced design, high quality, good plasticizing and low energy consumption. 2.It has the advantages of low noise, smooth operation, large loading and long life. 3.The technology can be adjusted according to customer’s raw material. Applicable materials:EPDM,PE,POE,EVA,PVC,materials plate/sheet etc. Products:car roor, car trunk plate, car mats, car interiors ,EVA sheet, insulation sheet for vehicle, interior sound insulation pad, car carpet, front enclosed sheet and the side enclosed sheet;etc.
ITEM SPECIFICATION MODEL WDE-5018 CAPACITY 250-350KG/H SCREW TYPE TWIN SCREW SCREW L/D 18:1 SCREW SPEED 0-700 R/MIN SCREW DIAMETER 50 MM MAIN MOTOR POWER 30 KW HEATING TYPE ELECTRICAL PIPES HEATING ZONE THREE COOLING TYPE WATER HEATING PIPES POWER 6.4 KW DRIVE MOTOR BRAND SIEMENS BRAND ELECTRICAL COMPONENTSBRAND Schneider FREQUENCY INVERTERBRAND Schneider ELECTRICAL POWER SPECIFICATION 380V 50 HZ, 3P.
As the segment structure design, the equipment can be configured with different l/d, barrel designs, screen changer, pelletizing system, and/or electric control, to best meet unique requirements of different process. Cause our better understanding of the different material, the screw con? guration is designed based on rich experience and software technology to accomplish the material conveying, plasticizing compounding, shear and dispersion and pressurization. Screw elements, accurately designed with cnc technology, are fully intermeshed, providing self-cleaning and easy interchangeability. Upgrading accuracy and quality of the standard and high torque gear box. The special new type barrel structure and screw elements been manufactured with our powerful design experience. Typical application Filler modification -caco3 -talc powder -barium sulfate -ceramic powder -wood/plant fiber -other inorganic fillers Reinforce modification -short glass fiber -long glass fiber -carbon fiber -other whiskers Masterbatch -carbon black masterbatch -color masterbatch -flame retardant masterbatch -degradable masterbatch -other function materbatch Compounding modification -thermoplastic/elastomer -polymer alloy Seaworthy packing
Hte series high torque twin screw compounding extruder set The structure and basic principle is similar with te series. Hte series comprehensive increase the application and ability of products with original german high torque gear box, lubricating system and torque limiter, Screw elements and key part of extruder, accurately manufactured with cnc technology which guaranteed the process accuracy effectively. Reasonable space and personnel usage with hte series Typical application Reinforce modification -short glass fiber -long glass fiber -carbon fiber -other whiskers Compounding modification -thermoplastic/elastomer -polymer alloy Seaworthy packing
Specifications: Plastic granulating line 1.Buiding block principle for a large variety of applications.Processing tasks can be optimally accomplished with only a few barrel and screw variations. 2.New design gearbox with high torque and high speed up to 600rpm. Receive the high output. 3.Iso9001 certificates kaiyou 4.Maching centers assures productsí» high quality. 5.Kaiyou manufactures and assembles a wide variety of auxillary devices. 6.Advanced plc control system. 7.A variey fo palletizing paterns can be choosed according to requirements. 8.High quality and competitive price Suitable for: 1.Polymer blending & filling modification 2.Engineering polymer & glass fiber reinforcement 3.Masterbatch, fuctional parent granule, special material, powder coating material and cable material reactive extrusion, degassing & devolatilization Model: hky-35 Screw diameter: 35.6mm Groove depth: 6mm L/d: 32~56 Main motor power: 18.5kw Screw speed: 600rmp Capability: 5-80kg/h Model: hky-50 Screw diameter: 50.5mm Groove depth: 9mm L/d: 32~56 Main motor power: 55kw Screw speed: 600rmp Capability: 100-300kg/h Model: hky-65 Screw diameter: 62.4mm Groove depth: 11mm L/d: 32~56 Main motor power: 90kw Screw speed: 600rmp 0
Features of the machine Because of the modular design of scroll and barrel, the model of thread, structure of barrel, draw ratio, feeding and exhaust data, conversion of network, the model of granulation, the electric equipment control mode can all be optimized and adjusted in the light of material system and the technological requirements. It is multifunctional as well as built for a special purpose. The machine is efficient with low specific energy consumption. The functional characteristics of TE series Bitruder include homoge neity, plastifying dying, fallibility, enhancement recovery and granulation. The host machine has modular design and the structure of screw and brrel are designed with precision by computer. It has perfect self purification and interchangeability. With planar triaxial reinforcement design and large safety capacity, new transmission torque dispensing equipment processes gear through high groove gear grinding. All the critical bearing is imported. The lubrication system is under interlock protection. The safe and reliable equipmene can stand wear and tear. Spiral shell's pole component of host computer connects with core axle and adopts the advanced involute spline to join the form. Change spiral shell pole association at will, in order to meeting different high polymer new material new technological requirements. The machine possesses various feeding structure and system. In accordance with different states of materials, the client may choose among single-scroll, twin-scrool, hollow spring engagement, nonengagement, forced side feeding and other modes. Fine vacuum exhaust and take off and wave device is effectively at to volatilize the composition supplies, Moisture and gas through releasing person who congeal the methods of vacuum discharge and shed, raise goods quality. In accordance with different technological rechirements, water cooing, oil cooling and qir cooling may be utilized. Various granulating systems, Air-cooling stick-drawing and particlecutting, air-cooling stick-drawing and particlecutting, aircooling rubbed thermal particlecutting, water-ring rubbed thermal particlecutting, off-centered spray thermal particlecutting and under rubbed thermal particlecutting. model Screw diameter (mm) Screw Rotary Speed (rpm) Motor Power(kw) L/D capacity (kg/h). TE-35 35.6 600 11-15 32-56 30-75 TE-50 51.4 500/600.
