Find Verified Jet A1 En590 10Ppm Suppliers, Manufacturers and Wholesalers

Automobile diesel fuel (EN 590) Grade E (winter), recommended for use at ambient temperatures up to minus 15 C (limiting filterability temperature). Diesel fuel EN 590 (EN 590) Grade E is obtained from petroleum refined products and is intended for use as automotive fuel for diesel engines of cars and trucks. Diesel fuel meets the requirements of the international standard EN 590/2000 and is characterized by a low content of sulfur, aromatic hydrocarbons and a high cetane number, which leads to an overall reduction in sulfur oxide emissions, a decrease in the amount of particulate matter in exhaust gases and the formation of deposits in the fuel system of cars and heavy vehicles, reducing exhaust smoke and is the key to good starting properties of the fuel during cold start of the engine. The oil refining industry produces diesel fuel in accordance with GOST 305-82 of three grades: L - summer, used at ambient temperatures above 0 C; 3 - winter, used at temperatures up to -20 C (in this case, winter diesel fuel should have a stagnation

Available stock in Rotterdam tank farm for jet fuel A1: CI DIP AND PAY FOB PROCEDURE 1. Buyer sends ICPO, Company Profile along with current and valid TSA company registration certificate+ buyer passport number + company profile to seller on receipt of seller's soft corporate offer. 2. Seller issues commercial invoice of the product in tanks at the port of Rotterdam and returns commercial invoice. 3.seller will provide the Proof of Product (PPOP) documents for product verification Which include Tank Storage Receipt (TSR) Certificate of origin Statement of Product Availability, Authorization to Verify (ATV), and Dip Test Authorization (DTA) Letter. 4.After successful verification of the PPOP, the buyer will contact the seller's Tank Storage Company to request a 1-day payment invoice to enable Buyer obtain all the necessary authorization and clearance for a Dip Test schedule. *Or* Buyer must have a minimum of 10 days TSR to avoid one day tank extension. 5.Upon a successful Dip Test conducted in the seller's tanks, the buyer will make the payment for the total product cost based on the SGS Report via MT103. The seller will transfer title ownership to the buyer and send all exportation documents. The buyer can then either transfer the product into a vessel or take over the seller's tanks for further storage. 6. Upon a successful Dip Test conducted in the seller's tanks, the buyer will make the payment for the total product cost based on the SGS Report via MT103. The seller will transfer title ownership to the buyer and send all exportation documents. The buyer can then either transfer the product into a vessel or take over the seller's tanks for further storage. 7. All intermediaries involved in the transaction will sign a Non- Circumvention, Non-Disclosure Agreement (NCNDA) and International Master Fee Protection Agreement (IMFPA). These documents will be forwarded to the seller for endorsement, and the seller will provide the Endorsed NCNDA/IMFPA and Authorization to Sell and Collect (ATSC).

The JET A-1 is type of aviation fuel, also called JP-A1, is used globally in the turbine engines[jet engines, turboprops] in civil aviation. ofr more information, contact Boggash Investment Limited as their official handles or website, thank you

PETROALLIANCE diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions. Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency. As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process. The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather. Our products are exported to Asia, Europe, America, and the CIS.

PETROALLIANCE diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions. Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency. As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process. The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather. Our products are exported to Asia, Europe, America, and the CIS.

Diesel is a light petroleum product, a complex mixture of hydrocarbons (with a carbon atom number of about 10-22), used as fuel for diesel engines. It is mainly composed of diesel fractions produced through processes such as crude oil distillation, catalytic cracking, thermal cracking, hydrocracking, and petroleum coking. It can also be produced through shale oil processing and coal liquefaction, and can be divided into two categories: light diesel (with a boiling point range of about 180-370 â??) and heavy diesel (with a boiling point range of about 350-410 â??). Widely used in large vehicles, railway locomotives, and ships. The most important use of diesel is for diesel engines in vehicles and ships. Compared with gasoline engines, diesel engines have higher thermal efficiency and lower fuel consumption. Diesel has low energy consumption, so some small cars and even high-performance cars have switched to diesel.

Russian Mazut M100 is a fuel oil that is manufactured to GOST specifications, GOST 10585-75 (not active), GOST 10585-99 Oil fuel (GOST is the Russian system of standards, much like ASTM, for example). Mazut is almost exclusively manufactured in the Russian Federation, This kind of oil is graded as the heavy furnace oil. The product is produced from the remains of raw oil processing. This kind of mazut is produced only from the low sulphur raw oil. This product is typically used for larger boilers in producing steam since the BTU content is high. The most important consideration (not the only consideration) when grading this fuel is the sulfur content, which can mostly be affected by the source feedstock. For shipment purposes, this product is considered a dirty oil product, and because viscosity drastically affect whether it is able to be pumped, shipping has unique requirements. Mazut is much like Number 6 Oil, and is part of the products left over after gasoline and lighter components are evaporated from the crude oil. The main difference between the different types of Mazut-100 is the content of sulphur. The grades are represented by these sulfuric levels: Very Low Sulphur is Mazut M100 with a Sulphur content of 0.5% Low Sulphur is Mazut M100 with a Sulphur content of 0.5% Normal Sulphur is a Mazut M100 with a Sulphur content of 1.0-2.0% High Sulphur is a Mazut M100 with a Sulphur content of 2.0-3.5% The amount of sulfur affects how clean the oil burns, and in turn the emissions it creates, as well as the amount of buildup that accumulates within the engines and furnaces that burns it. M100 prices are often determined by its point of origin and mode of production. Apart from shipping charges and regulations, product quality is considered to be more essential. When petroleum is distilled, fuel oil is produced as a residue or distillate. Any fuel oil is a form of petroleum that is burned to produce energy or heat for running an engine. These are usually low-quality oils that are heated in a furnace or boiler and used in a number of industries. MAZUT is such fuel and is typically used in generating plants and factories. Of course, different plants have expected requirements and specifications of their fuel and this is why MAZUT M100/99 and GOST 10585-75 are produced according to industry ISO standards.

D6 is also be known as Residual Fuel Oil and is of high-viscosity. This particular fuel oil requires preheating to 220 - 260 Degrees Fahrenheit. D6 is mostly used for generators. D6 is a type of residual fuel, mainly used in power plants and larger ships. The fuel requires to be preheated before it can be used. It is not possible to use it in smaller engines or vessels/vehicles where it is not possible to pre-heat it. D6 is its name in the USA. In other parts of the world it has other names. Residual means the material remaining after the more valuable cuts of crude oil have boiled off. The residue may contain various undesirable impurities including 2 percent water and one-half percent mineral soil. D6 fuel is also known as residual fuel oil (RFO), by the Navy specification of Bunker C, or by the Pacific Specification of PS-400 Recent changes in fuel quality regulation now require further refining of the D6 in order to remove the sulfur, which leads to a higher cost. Despite this recent change, D6 is still less useful because of its viscosity as well as that it needs to be pre-heated before it can be used and contains high amounts of pollutants, such as sulfur. Since it requires pre-heating, it cannot be used in small ships or boats or cars. However large ships and power plants can use the residual fuel oil. The price of D6 diesel traditionally rises during colder months as demand for heating oil rises, which is refined in much the same way.In many parts of the United States and throughout the United Kingdom and Australia, d6 diesel may be priced higher than petrol. D6 Diesel Standards and ClassificationCCAI and CII are two indexes which describe the ignition quality of residual fuel oil, and CCAI is especially often calculated for marine fuels.

Refined Sunflower Seed Oil Product - sunflower oil Processing - Refined Transparency - without lees Smell and taste - depersonalized oil odourless Color number,mg of iodine - 10 Acid value,mg kon/g - 0.25 Mass fraction of not fat admixtures,% Absence Peroxide value O2 Mmol/kg - 2.0 Mass fraction of moisture and volatiles content,% 0.10 Mass fraction of phosphorus-containing substances in terms of stearooleoletsytyn,% Absence It's a non-volatile oil pressed from the seeds of the sunflower and is commonly used as an oil for frying. ... It's a non-volatile oil pressed from the seeds of the sunflower and is commonly used as an oil for frying. Our sunflower oil corresponds to the Premium grade. Ideal for frying and for salads. This is a good nutritious food product rich in vitamin E, as it is produced by cold pressing without chemical extraction. In the refining process, chemical solvents are also not used, which leaves the oil even after refining very rich in vitamins and vegetable fats with a minimum oxidation index, which gives an shelf life of up to 18 months. I am sure you will be glad to have in your arsenal our competitive oil at a price corresponding to quality.

Bitumen a black viscous mixture of hydrocarbons obtained naturally or as a residue from petroleum distillation. It is used for road surfacing and roofing. Bitumen is a mixture of Organic Liquids that are highly Viscous, Black, Sticky, Entirely Soluble in Carbon Disulfide, and composed primarily of highly condensed Polycyclic Aromatic Hydrocarbons. Naturally occurring or crude bitumen is a sticky, tar-like form of petroleum which is so thick and heavy that it must be heated or diluted before it will flow. At room temperature, it is much like cold molasses. Refined Bitumen is the residual (bottom) fraction obtained by fractional distillation of crude oil. It is the heaviest fraction and the one with the highest boiling point, boiling at 525 C (977 F). Petroalliance are involved in import and the supply and trade of Bitumen Oil. This oil is a dark and viscous liquid which is sticky in texture. It is widely used in road construction, waterproofing, paints, enamels etc. It is available to clients in different types of settings at highly affordable prices. It is widely acclaimed amongst our client base for its supreme quality. Uses of Bitumens Bitumen is primarily used for construction and paving of roads. Its other uses are for Bituminous Waterproofing Products, including the use of bitumen in the production of roofing felt and for sealing flat roofs.

Petroalliance diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions. Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency. As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process. The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather. Our products are exported to Asia, Europe, America, and the CIS

Modern mineral base oils are the result of a long and complex distillation and refining processes. The feedstock used is crude oil. This substance is not of uniform quality but consists of several thousands of hydrocarbon compounds in which the elements carbon and hydrogen are present in all molecules and, in part, are bound to other elements. The hydrocarbons can be divided into three main groups: paraffinic, naphthenic and aromatic. Paraffinic hydrocarbons can be further divided into two subgroups: normal paraffinic and iso- paraffinic. Paraffinic hydrocarbons are the best lubricants. The distillation process in the refinery separates the hydrocarbons contained in the crude into cuts based on the molecule size. Furthermore, as many unwanted substances as possible are removed in the process, such as sulphur, aromatic hydrocarbons, paraffin wax, etc. In other words the mineral oil production process is physical cleaning and the end product is so-called paraffinic base oil. Most of the hydrocarbons in the base oil are paraffinic, but it also contains naphthenic and aromatic molecules. When the finished lubricant, such as motor oil, is made of these, several additive compounds are used to improve the base oil properties. The final outcome can also be so-called naphthenic base oil, where most of the hydrocarbons are naphthenic. Their cold properties are excellent.

REBCO (Russian Export Blend Crude Oil) is a sort of Russian Export Crude Oil with a mixture formed in the system of pipeline Transneft by mixing heavy sour crude Ural from the Volga region and low-sulfur oil in Western Siberia, the relevant characteristics to the brand Urals. Urals brand oil is supplied through the Baku-Novorossiysk pipeline system and the Druzhba pipeline. Components of petroleum are separated using a technique called fractional distillation, i.e. separation of a liquid mixture into fractions differing in boiling point by means of distillation, typically using a fractionating column. Petroleum includes not only crude oil, but all liquid, gaseous and solid hydrocarbons. Our company exports to contries such as Malasia, Singapore, China, Taiwan and all countries in Europe and parts of Africa We'll be glad to have a deal with you.

Petroalliance is a professional supplier for all kinds of coke products. Such as Semi coke, metallurgical coke, Foundry coke, Petroleum coke , Pitch coke and so on. We can provide different quality products according to the needs of our customers. We are trying to deliver a superme service for our customers including any packing orders, transportation and technical support. The company has get the dangerous chemicals business license and ISO 9001 certificate. Our product, service and manufacture have been kept high quality, good performance and environmental friendly all the time. We would have put lots of efforts on high quality products and services to keep a good relationship with our customers.

Uses of base oil sn500 Base oil sn500 use in manufacturing of many lubricants oil , who produce base oil mostly use sn500 as additive in their other product also blenders and compounders are other user of base oil different grades as well as sn500 , mostly base oil add from 1% up to 20% as additive to other products . base oil use in different oil as well is engine oil , motor oil , hydraulic oil , gear oil etc.