Cable Harness Probe Pogo Pin CHL165-HQ(8.3) for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHL165-HQ(8.3) harness probe we will introduce here is 1.65 mm in diameter and 35.8 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 100 milliohms. It is suggested the plunger be pressed at a distance of 3.5 mm at most when this probe works, although the plunger can move as far as 5.3 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 3.5 mm, its loaded force is about 113 gf, namely 4 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 100 milliohms Full Stroke: 5.3 mm Rated Stroke: 3.5 mm Spring Force: 113�±35 gf (4 oz) at load 3.5 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: Beryllium Copper, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
COCO PEAT BRICK is a compressed natural material produced from coconut husk. Due to its high-water absorption & air porosity property, it is used as a plant growing media. It is commonly delivering in 650 gm block. Specification (* shall be changed based on buyer's expectation) EC : < .8 millimhos / cm ( 1:1.5 dilution test ) pH : 5.5 - 6.5 Moisture :10 - 15 % Compression Ratio : 8 : 1 Expanded volume : 8 - 9 L Size : 20 x 10 x 5 cm Weight : 650 gm ( + / -30 gm) Package : Palletized or 24.5 MT in Carton Box Total blocks : 2000 Bricks per pallet,20 Pallet per 40' HC Loadability : 26 MT ( + / - 0.5 MT ) in 40'HC
Item condition: second hand Interchange Part Number: 2011 2012 2013 2014 2015 2016 2017 2018 11 12 13, CHRYSLER AWD ALL WHEEL DRIVE SRT-8 8 MOPAR, P53022071GB, 53022071 Manufacturer Part Number: R8193010AA Number of Cylinders: 8 Engine Size: 6.4L Fuel Type: Gasoline Brand: FACTORY ORIGINAL GENUINE JEEP SRT8 8 4 DOOR SUV Fitment Type: Direct Replacement Mileage: 71K Warranty: 60 Day UPC: Does not apply Items Size Qty Box  Dimensions 22X11X7.3 cm 100 Pcs/Box Carton Dimensions 38 X23.5 X 23.5 cm 1000 Pcs/Carton=10 Boxes Total Weight/Carton S:4.6kg M:4.8kg L:5.3kg XL:6.0kg Container Cartons Boxes Pcs 1x 20GP 1400 Cartons 14,000 Boxes 1,400,000 Pcs 1 x 40GP 2600 Cartons 26,000 X ½ X Boxes 2,600,000 Pcs 1x40 HQ 3233 Cartons 32,330 Boxes 3,233,000 Pcs Certificates & Test Reports All our Certifications & Tests are Real No. Items Certifications & Tests 1 Factory Quality Certifications ISO13485, ISO9001, BSCI 2 EU Markets EN455 1-3 Test, DOC - EU Registration, German DIMI, EN374 1-5 Test EN374 CEEN21420 - EN16523 3 US Markets U.S. 510K, FOOD Grade Test, Reach Test RoHS,ASTM D6978, ASTM D6319 4 Others Acute Systemic Toxicity Test, Skin Irritation Test, Skin Sensitization Test, GB10213, GB4806
Item details Item status : second hand Seller notes : CONDITION: REMANUFACTURED BLOCKENGINE WAS RUNNING GREAT BLOCK IS BARLEY USED REMANUFACTURED IN 6/22/2020, TO WATCH THE CAR RUNNING VIDEO LINK IS BELOW...." Item condition: second hand Interchange Part Number: 2011 2012 2013 2014 2015 2016 2017 2018 11 12 13, CHRYSLER AWD ALL WHEEL DRIVE SRT-8 8 MOPAR, P53022071GB, 53022071 Manufacturer Part Number : R8193010AA Number of Cylinders : 8 Engine Size: 6.4L Fuel Type : Gasoline Brand : FACTORY ORIGINAL GENUINE JEEP SRT8 8 4 DOOR SUV Fitment Type: Direct Replacement Mileage : 71K Warranty: 60 Day UPC : Does not apply Items Size Qty Box Dimensions 22X11X7.3 cm 100 Pcs/Box Carton Dimensions 38�?23.5�?23.5 cm 1000 Pcs/Carton=10 Boxes Total Weight/Carton S:4.6kg M:4.8kg L:5.3kg XL:6.0kg Container Cartons Boxes Pcs 1x 20GP 1400 Cartons 14,000 Boxes 1,400,000 Pcs 1 x 40GP 2600 Cartons 26,000 Boxes 2,600,000 Pcs 1x40 HQ 3233 Cartons 32,330 Boxes 3,233,000 Pcs Certificates & Test Reports All our Certifications & Tests are Real No. Items Certifications & Tests 1 Factory Quality Certifications ISO13485, ISO9001, BSCI 2 EU Markets EN455 1-3 Test, DOC EU Registration, German DIMI, EN374 1-5 Test EN374 CE EN21420 EN16523 3 US Markets U.S. 510K, FOOD Grade Test, Reach Test RoHS,ASTM D6978, ASTM D6319 4 Others Acute Systemic Toxicity Test, Skin Irritation Test, Skin Sensitization Test, GB10213, GB4806
YELLOW MAIZE FOR HUMAN AND ANIMAL CONSUMPTION Commodity Yellow maize Admixture 1.5 % max Color Yellow normal Moisture 14 % max Broken kernels 5 % max Aflatoxin 20 PPB max Protein 8 % min Discolored 3 % max Foreign Materials 0.5 % max Damaged Grains 1.5% max Test Weight -68kg/HI TDK 5 % max Sand 1.5% max Mercury 0.5 PPM max Cadmium 2.5 PPM max Heat Damage : 0.5 %max MOQ. :54mt Common types: Yellow Corn White corn Red corn Features: High nutritive value Premium quality Longer shelf life Pure Sweet taste
Wire Harness Probe Pogo Pin CHL165 for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHL165 harness probe we will introduce here is 1.65 mm in diameter and 35.4 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 100 milliohms. It is suggested the plunger be pressed at a distance of 3.5 mm at most when this probe works, although the plunger can move as far as 5.3 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 3.5 mm, its loaded force is about 113 gf, namely 4 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 100 milliohms Full Stroke: 5.3 mm Rated Stroke: 3.5 mm Spring Force: 113�?�±35 gf (4 oz) at load 3.5 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980.Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
detergent powder washing top brand detergent washing powder washing powder detergent Laundry Soap Specification item value Type Other detergent Function water soluble Laundry Pods 1. We could design any shape or customized formula for laundry detergent pods/ laundry gel pods/fragrance booster/ laundry scent beads / Dish washing tablet / as your requests, so just tell us what you want. We will absolutely satisfy you! 2. We will offer professional suggestions, send you samples to confirm before we make your order. Product Name: Laundry detergent pod Other Name: Laundry capsule, laundry beads, laundry gel pod Material: Water-soluble PVA film and high-concentrated laundry liquid Feature: Eco-Friendly, Quantitative use, Strong removal Payment: T/T bank transfer Color: Customized fragrance: Customized Product Characteristics 1. Safe and mild: formulated to prevent rashes and skin irritation, suitable for sensitive skin, allergies, eczema, psoriasis, infants and pets. Mild in delicate close-fitting and natural fabrics (cotton, wool, Cashmere) 2. For all machines: optimized HE, high efficiency, standard, front loader and top loader washing machine performance 3.Carefully formulated: Using protease, fibrase imported from Denmark, and water-soluble membrane imported from Japan. It hasnâ??t been tested on animals. Free of synthetic fragrances, dyes, enzymes, optical brighteners, Paraben, phosphates and propionate 4.Low waste packaging: recyclable and compostable cardboard packaging helps reduce disposable plastic Our Advantages Laundry detergent pod four effects in one, set clean, smooth, bactericidal, color protection, fragrance as one One pod> Laundry detergent + antibacterial solution + softener + perfume1The effective surfactant reaches 80 percent, has eight times the cleaning power, can effectively remove 99 percent of the stains. 2. Denmark imported protease, strong stain removal, 1 pod can wash 1 large bucket of dirty clothes, 8g pod can wash 8-10 clothes,12g pod can wash 14-18 clothes, 15g pod can wash 20-25 clothes. 3. Antibacterial 99%, dry and not easy to mold. 4. Japan imported water soluble film, water soluble fast, no residue. 5. No phosphorus and no fluorescence brightening agent, safe ingredients, pregnant women and babies can rest assured to use. 6.Less foam when washing clothes, and there will be no foam residue after washing. Low foam is easy to clean, greatly reducing laundry time, but also saves water and electricity, the choice of environmentally friendly life.
Moisture 12-13% Max Protein 8-9% Max Purity 98% Admixture 2.5% Max Test Weight 72 kg/hl min Discolored & Damaged < 5% Broken & Foreign materials < 5% Dust / Sand Silica < 2 % Ash 1.60 Max Fat 5% Max Total Aflatoxin 20 PPB max Total Funmonisin 60 PPM Max
Product Name: Magnesium Aluminum Silicate "Origin: China CAS No.: 71205-22-6 AUCO No.: 954 Packing: 25kg drum" Items Standard Characteristics Almost white to off white free flowing,tasteless odorless,slippery granules or flakes(Completely free from foreign and black particles) Solubility Dispersaible in water Identification Responds to tests for identification PH(5% w/v) 9-10 Water N.M.T 8% Residue on ignition N.M.T 17% Viscosity(5% w/v) 800-2200 cps(Dispersion) Acid Demand N.M.T 4% Particle size Less than 250 micron for granules and for flakes less than 1mm length and less than 250 micron thickness Arsenic N.M.T 3 ppm Heavy metals N.M.T 15 ppm A1/Mg ratio 0.5-1.2 Microbial Limit "No pathogenic strains less than 100 cfu/g bacteria less than 100 cfu/g fungi and yeast"
Product Name: Magnesium Aluminum Silicate "Origin: China CAS No.: 71205-22-6 AUCO No.: 954 Packing: 25kg drum" Items Standard Characteristics Almost white to off white free flowing,tasteless odorless,slippery granules or flakes(Completely free from foreign and black particles) Solubility Dispersible in water Identification Responds to tests for identification PH(5% w/v) 9-10 Water N.M.T 8% Residue on ignition N.M.T 17% Viscosity(5% w/v) 800-2200 cps(Dispersion) Acid Demand N.M.T 4% Particle size Less than 250 micron for granules and for flakes less than 1mm length and less than 250 micron thickness Arsenic N.M.T 3 ppm Heavy metals N.M.T 15 ppm A1/Mg ratio 0.5-1.2 Microbial Limit "No pathogenic strains less than 100 cfu/g bacteria less than 100 cfu/g fungi and yeast"
Product Name: Magnesium Aluminum Silicate "Origin: China CAS No.: 71205-22-6 AUCO No.: 954 Packing: 25kg drum" Items Standard Characteristics Almost white to off white free flowing,tasteless odorless,slippery granules or flakes(Completely free from foreign and black particles) Solubility Dispersaible in water Identification Responds to tests for identification PH(5% w/v) 9-10 Water N.M.T 8% Residue on ignition N.M.T 17% Viscosity(5% w/v) 800-2200 cps(Dispersion) Acid Demand N.M.T 4% Particle size Less than 250 micron for granules and for flakes less than 1mm length and less than 250 micron thickness Arsenic N.M.T 3 ppm Heavy metals N.M.T 15 ppm A1/Mg ratio 0.5-1.2 Microbial Limit "No pathogenic strains less than 100 cfu/g bacteria less than 100 cfu/g fungi and yeast"
QUALITY PARAMETER SPECIFICATION Varietal Purity Min (% by count) NA Moisture Max (%) 12.5 Protein Min (%) NA Protein Max (%) NA Test Weight Min (kg/hl) 62.5 Retention Min (% by weight) NA Screenings Max (% by weight) 15.0 Germinative Energy Min (%) NA Germinative Capacity Min (%) NA Rapid Visco Analyzer Min (units) NA Falling Number Min (sec) NA Defective Grains Max - (% by count, 100-grain sample, unless otherwise stated) Shot N/A Sprouted Nil Dark Tipped NA Field Fungi NA Skinning NA Insect Damaged (count per half a liter) 85 Foreign Seed Contaminants Max - (count of seeds in total per half liter, unless otherwise stated) Foreign Grain 500 Variation a 50 Variation b 100 Type 1 (individual seeds) 8 Type 2 Nil Type 3a 2 Type 3b 4 Type 3c 4 seeds / 1 pod Type 3d 1 Type 4 20 Type 5 40 Type 6 40 Type 7a 10 Type 7b 150 Small Foreign Seeds (% by weight) 1.2 Other Contaminants Max - (count per half liter, unless otherwise stated) Foreign Material (% by weight) 1.0 Cereal Smut / Cereal Ergot (entire load) Nil Loose Smut (weight in grams) 0.1 Ryegrass Ergot (length in cm) 0.5 Pickling Compounds or Artificial Color (entire load) Nil Chemicals Not Approved for Barley (entire load) Nil Stored Grain Insects & Pea Weevil Live (entire load) Nil Insects Large, Live, or Dead 3 Insects Small, Live, or Dead 10 Snails 1 Sand 50 Earth 3 Stones (g per 2.5L) 4.0 Objectionable Material (entire load) Nil
1) Mortise Locks 2) Pad Locks 3) Cam Locks 4) Safe Locks 5) Furniture Locks 6) Euro Cylinder Locks 7) Multipurpose Locks 8) Pin Locks 9) Door Locks 10) Night Latch Locks 11) Door Handles 12) Pull Handles 13) Mortise Handles 14) Glass Handles 15) Cabinet Handles 16) Door And Cabinet Konbs 17) Wall Hooks 18) Coat Hooks 19) Door Fittings 20) Hinges 21) Tower Bolt 22) Furniture Hinges 23) Aldrops 24) Door Knowcker 25) Door Stopper 26) Door Closer 27) Bathroom Fittings
No. Description of test 1. Brix 25.5 2. Salt 1.5 3. PH 4-4.03 4. Color brix: 12.5 - a/b Minimum: 2 5. Viscosity bostwick brix: 12.5- a/b 6-6.5 6. Organoleptic properties Negative 7. Black particle, seed and skin Negative 8. Aerobic mesophilic bacteria (per 1 gr) Negative 9. Aerobic thermophilic bacteria(per 1 gr) Negative 10. Mold & yeast(per 1 gr). Negative 11. Howard No =
FRANCE WAREHOUSE, DDP EUR 82.73 USA warehouse ddp USD 90.99 UK warehouse DDP GBP 55.33 Specification 1. Brand: Jingyuan 2. Material: MDF Density Board 3. Process: Piano Paint 4. Packing: Carton Pearl Cotton 5. Product Dimensions: (19.29 x 19.88 x 19.09)" / (49 x 50.5 x 48.5)cm (L x W x H) 6. Packing Dimensions: (22.64 x 8.66 x 24.41)" / (57.5 x 22 x 62)cm (L x W x H) 7. Gross Weight: 22.05lb / 10kg 8. Test report: ASTM F963 16CFR Package Includes: 1 x Wooden Piano 1 x Chair 1 x Music Stand 1 x Music Score 1 x Phonetic Card 1 x Phonetic Sticker 1 x English Manual
Item Parameters Specified Value 1. Appearance Clear, transparent, without water and a) Visual suspended particles at ambient temperature . b) Color (Saybolt Scale Points) Not specified, analysis to be required c) Total sediments, mg/dm max - 1.0 2. Acidity, mg KOH/g, max - 0.10 3. Aromatic hydrocarbons, vol. %, max - 25.0 4. Mercaptan sulphur, wt. %, max - 0.0030 Or Doctor test negative 5. Total sulphur, wt. %, max - 0.25 6. Distillation, C 10% distillated at temperature, C not higher than 205.0 50% distillated at temperature, C Not specified, analysis to be required 90% distillated at temperature, C not higher than 300.0 residue, %, max 1.5 losses, %, max 1.5 7. Flash point, C, not lower than - 38.0 8. Density at 15 C, kg/m - 775.0-840.0 9. Pour point, C, not higher than - Minus 47.0 10. Kinematic Viscosity at minus 20C, - 8.000 m /s, max 11. Net calorific value, MJ/kg, min - 42.80 12. Smoke point, mm, min - 25.0 or with naphthalene hydrocarbons - 19.0 vol.% = max. 3%,min. 13. Copper corrosion test at 100C, during 2 h �?�± 5 min, - 1 during 2 h �± 5 min, class, max 14. Thermal oxidation stability - 3.3 (25.0) determined by JFTOT at Temperature not lower than 260 �?�°C, - 3 during 2.5 h Pressure drop at filter, Without any deposits of abnormal or kPa (mm Hg), max Deposits on tube, less than peacock (iridescence) color 15. Actual gum concentration, - 7 mg/100 c , max. 16. Interaction with water : a) state of interface, points, max - 1b b) light transmission measurement - 85 by micro separator, min. without antistatic additive 17. Specific conductivity, pSm/m, - 10 for fuel without antistatic additive, max. 18. Lubricity : wear scar diameter, mm, max - 0.85
JET FUEL A1 Spot & Contract FOB basis 80 $ to 83 $ based on quantity Procedure : TANK TO TANK FOB PROCEDURE: 1. Buyer issues ICPO with company letterhead, buyer�¢??s information, passport copy and banking information. 2. Seller issues a Commercial Invoice (CI) and Buyer signs and returns back the Commercial Invoice along with Buyer's Tank storage agreement (TSA). 3. Seller Representative visit the buyer's tank farm for TTM with a copy of the SGS and Injection Report upon verification of the copy of the SGS and Injection report, buyer and buyer's Tank Farm endorse DIP Test Authorization letter seller sends the following PPOP documents: * Certificate of Product Origin. * Letter Of Guarantee. * Statement of availability of product. * Product quality passport (Analysis test Report). 4. Seller issues Complete DTA and Tank Receipt to Buyer, Buyer order SGS to conduct a Dip Test of the product in the Seller's Tank on Buyer expenses submit the full injection report to the Buyer. 5. Upon successful Dip Test, sellers inject the fuel into the buyer lease Storage Tank and sellers submit the full injection report to the Buyer. 6. Buyer makes 100% payment by MT103 TT wire transfer for the total product and the Seller pays the commission to all intermediaries involved in the transaction within 24 hours after confirmation of the buyer's payment. 7. Seller issues draft SPA to the buyer to review for R&E monthly deliveries. 8. Buyer review and approves the SPA and issues DLC MT700or SBLC MT760 irrevocable, non-transferable, auto revolving for 12 months shipment value, Financial Instrument for length of the contract, and for each lift per schedule. Buyer pays after Dip Test by MT103 Wire Transfer each monthly quantity. 9. The subsequent delivery shall commence according to the terms and conditions of the contract. Seller pays commissions to all intermediaries as per IMFPA/NCNDA 24 hours after receiving payment from the buyer.
Wire Harness Probe Pogo Pin CHD136 for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of the automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHD136 harness probe we will introduce here is 1.36 mm in diameter and 33 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 50 milliohms. It is suggested the plunger be pressed at a distance of 4.6 mm at most when this probe works, although the plunger can move as far as 7 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 4.6 mm, its loaded force is about 255 gf, namely 9 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Full Stroke: 7 mm Rated Stroke: 4.6 mm Spring Force: 255�±75 gf (9 oz) at load 4.6 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: Beryllium Copper, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980.Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Cable Harness Probe Pogo Pin CH136 for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CH136 harness probe we will introduce here is 1.36 mm in diameter and 33  mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 50 milliohms. It is suggested the plunger be pressed at a distance of 1.67  mm at most when this probe works, although the plunger can move as far as 2.5  mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 1.67 mm, its loaded force is about 140  gf, namely 5  ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Full Stroke: 2.5 mm Rated Stroke: 1.67 mm Spring Force: 140 ±40 gf (5 oz) at  load 1.67 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
Cable Harness Probe Pogo Pin CHZ199 Series for Electronic Test Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHZ199 harness probe we will introduce here is 1.99 mm in diameter and 33.2 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 50 milliohms. It is suggested the plunger be pressed at a distance of 4.4 mm at most when this probe works, although the plunger can move as far as 6.6 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 4.4 mm, its loaded force is about 133 gf, namely 4.7 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Full Stroke: 6.6 mm Rated Stroke: 4.4 mm Spring Force: 133�?�±40 gf (4.7 oz) at load 4.4 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated For more information, please check below catalog. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
