SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc ( +10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80 C. When the DC panel has a temperature over 100 C, the module will stop working; when the DC panel has a temperature below 90 C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
The Variable Speed Drive FRENIC series is equipped with functions and performance to meet all types of requirements, and in addition it is easily maintained and environmentally friendly. The series lineup ranges from simple to advanced-function models, enabling model choices matching situations for use. Fuji Electric provide Variable Speed Drives perfect for automating and with energy saving devices like a fan pump or carrier and variable speeds.
Type: Outboard Motor Year: Current Model: F40 HP Jet Drive Model Number: F40JEHA Series: Four Stroke Jet Drive HP: 40 Engine Type: 3 Cylinder Displacement: 45.6 ci (747 cc) Borex Stroke: 65 x 75 mm (2.56 x 2.95in) Prop Shaft Horsepower: 30 @ 5500 RPM Compression Ratio: 9.4 RPM Range: 5000-6000 Fuel Induction System: EFI (SOHC) Fuel Type: Unleaded gasoline (minimum pump octane 87) Exhaust: Thru prop Ignition System: TCI Microcomputer CARB Rating: 3-Star Alternator Outputat WOT: 16A Starting System: Electric Lubrication: Wet Sump Oil Capacity: 2.1 quarts Recommended Engine Oil: Yamalube 4M Gear Ratio: Direct Drive Control Type: Tiller Handle Trolling Throttle Adjustment: N/A Cooling: Water, Thermostatic Control Gear Shift: F-N-R Command Link System: No Enhanced Ultimate Corrosion Protection System UCP: Standard Feature Power Trim and Tilt: No Shaft Length: 20 inch Gearcase Rotation: Jet Drive Propeller: Jet Drive Tiller Handle Kit: Optional Freshwater Flush: Yes
Professional Honey Bee Tools Nuc Box Metal Entrance / Plastic Beehive Entrance Basic Information Place of Origin: China Brand Name: Super-sweet Minimum Order Quantity: 1000 Packaging Details: beehive disc entrance for beehive tools 1. Standard Package. 2. at your request Delivery Time: 5 working days Payment Terms: L/C, D/P, T/T, Western Union, MoneyGram Supply Ability: 100000 Piece/Pieces per Month Product Description Bee Hive Nuc Box Metal Entrance Disc Enter For Bee Plastic Entrance Gates Products Name: plastic beehive entrance Material : metal Weight:17g/pc Diameter:7cm Color: green,white Company Information 1. We are the professional manufacturer of beekeeping equipment tools specialized in designing, researching, developing molding and producing, selling and exporting various beekeeping supply. We have a complete set of mold development and production equipment, and provide various and new beekeeping devices for all beekeepers. 2. Other series products: Beekeeping Equipment 1) Beeswax comb foundation roller (manual embossing roller) & (electric embossing roller) 2) Beeswax comb foundation roller (automatic edge cutting) 3) Beeswax comb foundation roller (manual plain roller) & (electric plain roller) 4) Honey extractor series 5) Basic beekeeping tools series 6) Queen rearing series 7) Beekeeping protective clothing series 8) Bee feeder and sprayer 9) Beehive and beeswax foundation
AS PS ABS PLA HDPE Granules Acrylonitrile - styrene copolymer. Acrylonitrile - styrene copolymer. A polymer composed of acrylonitrile and styrene.Typically 15-50% styrene.Transparent solid with yellow to amber needle color.The density of 1.06.It's thermoplastic.Not easy to change color.It is unaffected by diluteacids,bases, alcohols and gasoline.But soluble in acetone, ethyl acetate, dichloroethylene and so on.Can be used as engineering plastics.Excellent heat resistance and solvent resistance. Application. 1. General grade: cassettes, trash cans, toothbrush handles, lamp covers, pen tube, Cup with cover, cosmetic cases. 2. Special grade: blade of fan, batteries housing, lighters. 3. Refrigerator Sleeves, Miscellaneous 4.Used for pots, cups, milk bottles, etc., with high transparency, safety and resistance to falling 5. High Transparency, Heat Resistance, chemical resistance PC + Glass Fiber reinforced (GF) The glass fiber (GF) reinforced PC have improved tensile / flexural properties as well as thermal resistance. The FR rating improves with increase in thickness and the material can acquire a UL94 V0 rating at 3 mm. Grade: (ML3410-30 / MH3515-30 / MN-3110-30) 1) ML series: ML3405 / ML3410 / ML3420 / ML3430 (10-30% GF) General GF reinforced PC for standard application, they are characterise by balance of stiffness, modulus and impact. Application: Watch parts, switches and nobs, OA equipment. 2) MH series: MH-3515 / MH-3520 / MH-3530 (10-30% GF) Special GF reinforcements for optimal balance between modulus and improved weld line performance. MH series also improve warpage and dimensional stabilities. Applications: Watch parts, laptop housings, optical devices, mobile accessories, TV frames. 3) MN series: MN-3110 / MH-3120 / MN-3130 (10-30% GF) MN series are specially formulated for various kinds of housings and cases. They are characterise by superior impact performance, surface aesthetics and weld line strengths. Applications: Meter cases, electrical and electronic housings.
Our impact sockets are available in a wide range of lengths and wall thickness and with single or double hex openings. Square openings are also available. Impact sockets are designed for use with powered impact wrenches where wrenches can be powered pneumatically (by compressed air) or electrically. The combination of wrench and impact socket can deliver greater torque to the head of a fastener. A few common types that are used are as under: 6 Point Standard Impact Sockets 6 Point Deep Impact Sockets 12 Point Standard Impact Sockets 12 Point Deep Impact Sockets 4 Point Standard 8 Point Standard Thin Wall Impact Sockets -Standard Thin Wall Impact Sockets-Deep
9TORC crowfoot wrench is a special wrench that is used  when you need to work around obstacles. Unlike socket wrenches, this wrench fits on a nut or bolt's side like a box wrench. A crowfoot wrench looks like a box wrench head, and it may be attached to a torque wrench for better performance. Crowfoot torque wrench enables you to reach inaccessible bolts and nuts that sockets alone can't reach, For those fasteners in odd places, there's the crowfoot to loosen bolt, coming in sizes ranging from 3/8 to 1.Great for Automotive & Motorcycle work, or for the Aircraft Mechanic, or even as a Plumber Wrench for Plumbers. Heavy Construction yet slim enough for tightest areas.
9TORC deals in electric pumps used for Torquing applications. Pumps come in two variants i.e. two stage and three stage. Three stage electric pumps have better efficiency and less maintenance since it gradually increases required pressure without any sudden rise. It can be operated on 110v and 220V. Our pumps are available in many configurations to give you the right power for the job with the capability to run multiple tools simultaneously. Available with electric power source.
Our Manual torque multipliers offer a range of output torques from manual inputs that can easily be achieved by an operator, providing accurate, efficient torque multiplication for make-up or breakout of joint fasteners. It is a simple gear box, works on the principle of â??Epicyclic Gearing. The given load at the input gets multiplied as per the multiplication factor & transmitted at the output, thereby with a minimum efforts you achieve greater load.
A Sq. drive hydraulic torque wrench is a fastener to achieve proper tightening or loosening of a connection using hydraulics. A torque wrench is applied to the nut either directly or in conjunction with. One-piece forming machine body made of aluminum titanium alloy, high strength, high tenacity and design to exert torque on toughest for a smaller 360�° click-on, multi position reaction arm with accuracy ± 3% Light weight, ergonomic design for easy handling & an easy fit even in application where access is limited 60 free positions in 360�°, easy positioning, capability of bearing the maximum torque at any angle Check pawl design critical for overcoming the back turn of the wrench, and improving both efficiency and torque precision
9TORCâ??s Torque Multipliers provides extra mechanical advantages needed to tighten or loosen stubborn nuts and bolts locate cramped or (in accessible) positions. A manual Tool, particularly recommended where no compressed air/electric power available for use of Power Tools. Overall, Torque Multipliers are the ones used for tightening and loosening heavy duty bolting connections. It reduces a lot of physical effort and act as a crucial support to apply torque more accurately.
EQUINAS TFO 60i High Quality Inhibited Transformer Oil EQUINAS TFO 60i is a high-quality inhibited insulating oil with very good dielectric properties and oxidation stability intended for transformers, switchgears, and other electrical equipment. Transformer Oil is a series of products blended using highly refined mineral oil and a selected antioxidant. It is designed for insulating and cooling transformers, oil-immersed switchgear and other electrical insulating applications. Does not contain harmful polychlorinated biphenyls (PCBs). Applications: Used as an insulating oil in transformers, switchgear, inductors, condensers, transducers, and similar equipment, also at low temperature in outdoor use It insulates current-carrying parts from each other and from ground, carries away heat, prevents glow discharges, extinguishes electric arcs in switchgear, and impregnates insulating materials Features and Benefits: Excellent insulating properties High dielectric strength (1) Low power factor Resists oxidation and deposit formation Excellent low-temperature properties Compatible with materials used in transformers Does not contain any PCBs Meets or exceeds the IEC 60296 Packages size: Available in drums and flexibags Health and Safety: Based on available information, this product is not expected to produce adverse effects on health when used for applications referred to above and the recommendations provided in the Safety Data Sheet (SDS) are followed. The SDS is available upon request through our sales contact office. This product should not be used for purpose other than the applications referred to above. If disposing of used product, take care to protect the environment, follow the local rules and regulations of your local Authority.
EQUINAS TFO 60u High Quality Un-Inhibited Transformer Oil EQUINAS TFO 60u is a high-quality un-inhibited insulating oil with very good dielectric properties and oxidation stability intended for transformers, switchgears, and other electrical equipment. Transformer Oil is a series of products blended using highly refined mineral oil and a selected antioxidant. It is designed for insulating and cooling transformers, oil-immersed switchgear and other electrical insulating applications. Does not contain harmful polychlorinated biphenyls (PCBs). Applications: Used as an insulating oil in transformers, switchgear, inductors, condensers, transducers, and similar equipment, also at low temperature in outdoor use It insulates current-carrying parts from each other and from ground, carries away heat, prevents glow discharges, extinguishes electric arcs in switchgear, and impregnates insulating materials Features and Benefits: Excellent insulating properties High dielectric strength (1) Low power factor Resists oxidation and deposit formation Excellent low-temperature properties Compatible with materials used in transformers Does not contain any PCBs Meets or exceeds the IEC 60296 Packages size: Available in drums and flexibags Health and Safety: Based on available information, this product is not expected to produce adverse effects on health when used for applications referred to above and the recommendations provided in the Safety Data Sheet (SDS) are followed. The SDS is available upon request through our sales contact office. This product should not be used for purpose other than the applications referred to above. If disposing of used product, take care to protect the environment, follow the local rules and regulations of your local Authority.
Max.Power consumption:1900w. Length239-297mm high282-320mm
The basalt fiber roving of our company adopts the new tank kiln method and 2400 hole large leakage plate to form basalt roving products With a series of advantages such as high strength, large modulus, good temperature resistance, good chemical corrosion resistance and good electrical insulation, basalt is produced with homogenized basalt raw materials, with excellent performance, stable quality and small dispersion coefficient. Basalt fiber roving is a new material to replace glass fiber and carbon fiber
Basalt Fiber Series Fabric 1. Production: basalt fiber fabric is made of continuous basalt fiber textile yarn through warping, weaving and coating. 2. Weaving methods according to requirements: unidirectional cloth, plain cloth, twill cloth and grid cloth. 2. Application: reinforced mesh cloth, fireproof cloth, fishing rod cloth, luggage decoration cloth, electrical insulation cloth, bulletproof cloth, etc. 3. Packaging: 100M / roll (or customized as required). 4. Performance: high strength, high temperature resistance, good electrical insulation, non hygroscopic, acid and alkali corrosion resistance.High temperature resistance 1000 �° C 5. Specification and model: bfw16 * 20-100 (120) BFW: basalt fiber fabric;Completely replace carbon fiber sheet building reinforcement 16 * 20: the warp and weft density of yarn is 16 and 20 pieces / cm respectively; 100: the width of the fabric is 100 cm; (120): the mass per unit area of fabric is 120 g / m2. BFNP5*5-200(160) BFNP: basalt fiber mesh cloth (coated and shaped); 5 * 5: the longitude and latitude mesh size of the cloth surface is 5 and 5mm; 200: the width of the grid is 200 cm; (160): the weight of grid cloth per unit area is 160g / m2.
Input Voltage 12V / 24V DC optional Output Voltage 115V / 230V AC optional Portable power for AC products, AC outlets for connecting multiple loads High surge capacity for products that require more power to start High efficiency converts virtually all of the battery's power to AC Mounting brackets for convenient installation Heavy duty stud-connection mounting RS232 communication port WIFI/BMS Optional Overload and over temperature shut down Low voltage and over voltage alarm/cut off Input reverse protection Short circuit protection PI15 series is a pure sine wave inverter, high frequency machine solution, the product is small size, the solution is reliable and stable, the main function is to invert the DC 12VDC battery or 24VDC battery to AC 230VAC or AC 115VAC output, mainly used for emergency use Electricity, car inverter, outdoor electricity and other occasions.
PHONE SCRAP HS Code 85437090 PRICE = US$400/TON CIF ORIGIN: THAILAND PACKAGE: 1KG,5KG,10KG,15KG,25KG,50KG MIN ORDER:100 TONS DESCRIPTION Product Description Dear client WE HAVE VERY HIGH YIELD GOLD RECOVERY CPU CERAMIC PROCESSOR SCRAPS AND COMPUTER MOTHERBOARD SCRAPS FOR SALE We can supply cpu ceramic processor scraps Intel 186 / 286 / 386 / 486 / Pentium / Pentium Pro / i860 / i960 Cyrix 486 / 586 / MIIIBM 486 / 586 / 686 Motorola 68000 / 88000 series NEC Toshiba MIPS series: R4000 / R8000 / R10000 / R12000 1-Gold Top Cpu... 2-Gold Top&Bottom Cpu.. 3-Intel 186/286/386/486/Pentium/Pentium Pro/i860/960/... 4-Cyrix486/586/MIIIBM486/586/686/ .. 5-RAM (memorys)... We can supply on monthly basis around 10-50 tons per month of Ceramic cpu scrap for gold recovery and scrap motherboards and lan cards. We also supply sample order from 100 KGS. Our prices changes according to your order. For bulk order or sample order, contact us for our quote. Specification and use: Usage: For electrical industries Suitable to manufacture numerous electrical components, cables, cans, etc 1.Motherboard And other Computer Scrap 2.Untested condition 3.For recycling 4.Stock available PS / ABS bales scrap-waste from electric and electronic devices (TV SHELL-CASE, COMPUTERS etc.) CAN LOAD IN 1X40\'HC CONTAINER APROX. 22 TONS (-+10%) We can sell you you the following scrap: Computer Mother Boards Computer Finger Boards Computer Memory Computer Processors Computer Power Supplies Computer Hard Disks Computer Floppy Drives Computer CD Rom Computer Cases Computer Wires Computer Keypads Computer Mouse Computer UPS or Lead batteries from UPS Cell Phone Handsets Cell Phone PCB Boards Cell Phone Batteries Lithium Cell Phone Batteries Nickel Cell Phone LCDs Cell Phone Housings Cell Phone Chargers
Napkins per Cycle 4 to 7. Power 230 V, 10 Amp, 50 Hz. Electric Heater - 800 W. Auto power cut off Yes. No. of napkins per cycle 4 to 7. No. of Cycles per day- 9 to 10 (in 12 hours). MS body PU painted. Housing External - CRCA Steel of 1.2 mm. Housing Internal - Insulated type. Insulation - Thermal ceramic sheet with Glass wool of 4-5 mm thick Emission Outlet - 2 inch on top. Flue gas pipe - 2 meter. Residue Ash - Sterlite Ash < 2gm per cycle. Door Design - Thermal insulated door. MCB rating - 16 Amp C Series. Electric cable - 2.5 meters. Dimensions (LXWXH) mm 320X230X520. Weight 18 kg
V5 Borewell Submersible Pumpset Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series) - 9 Mtr. Head Per Stage In Radial Flow Series. - Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads. - Dynamically balanced roating parts ensure minimum vibration and longer life - Motor Portion covered with corrosion resistant S.S. J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS pumps are available in (GRS - Series) Specification - Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply (Single Phase available in 3 HP to 5 HP) - Speed : 2880 RPM - Head Range : 12 Mtr. To 640 Mtr. - Discharge Range : 690 LPM to 80 LPM - Outlet Size in Inch : 1.5 , 2.0" & 2.5" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW, 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2 kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star Delta (SD) upto 9.3 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
